YOKOGAWA DLM4038 - Page 56

5-23
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
Command Function Page
:SERialbus<x>:CAN:SEARch:SETup[
:IDData]:MSIGnal:SIGNal:DECimal
<y>
Sets a signal’s reference value, which is one of the ID and data conditions,
for CAN bus signal searching in decimal notation.
5-163
:SERialbus<x>:CAN:SEARch:SETup[
:IDData]:MSIGnal:SIGNal:ITEM
Sets the signal item, which is one of the ID and data conditions, for CAN bus
signal searching.
5-163
:SERialbus<x>:CAN:SEARch:SETup[
:IDData]:RTR
Sets or queries the RTR value, which is one of the ID and data conditions,
for CAN bus signal searching.
5-163
:SERialbus<x>:CAN:SEARch:SETup:
MODE
Sets or queries the CAN bus signal search mode setting. 5-163
:SERialbus<x>:CANFD?
Queries all CAN FD bus signal settings. 5-163
:SERialbus<x>:CANFD:ANALyze?
Queries all CAN FD bus signal analysis settings. 5-163
:SERialbus<x>:CANFD[:ANALyze]:S
ETup?
Queries all CAN FD bus signal analysis bus settings. 5-163
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:BRATe
Sets or queries the CAN FD bus signal analysis bit rate (data transfer rate). 5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:DBRate
Sets or queries the CAN FD bus signal analysis data bit rate (data transfer
rate of data phase).
5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:DSPoint
Sets or queries the CAN FD bus signal analysis data phase sample point. 5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:FDSTandard
Sets or queries whether the CAN FD bus signal to be analyzed is an ISO
standard signal.
5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:RECessive
Sets or queries the CAN FD bus signal analysis recessive level. 5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:SOURce
Sets or queries the CAN FD bus signal analysis source. 5-164
:SERialbus<x>:CANFD[:ANALyze]:S
ETup:SPOint
Sets or queries the CAN FD bus signal analysis sample point. 5-165
:SERialbus<x>:CANFD:DETail?
Queries all CAN FD bus signal analysis result list settings. 5-165
:SERialbus<x>:CANFD:DETail:DISP
lay
Sets or queries the display mode for the CAN FD bus signal analysis result
list.
5-165
:SERialbus<x>:CANFD:DETail:LIST
:ITEM?
Queries all items that will be displayed in the CAN FD bus signal analysis
result list.
5-165
:SERialbus<x>:CANFD:DETail:LIST
:VALue?
Queries all the data for the specified analysis number in the CAN FD bus
signal analysis result list.
5-165
:SERialbus<x>:CANFD:SEARch?
Queries all CAN FD bus signal search settings. 5-165
:SERialbus<x>:CANFD:SEARch:ABO
Rt
Aborts the CAN FD bus signal search. 5-165
:SERialbus<x>:CANFD:SEARch:EXEC
ute
Executes a CAN FD bus signal search. 5-165
:SERialbus<x>:CANFD:SEARch:FJUM
p:ACK
Jumps to the ACK Field in the CAN FD bus signal search result. 5-165
:SERialbus<x>:CANFD:SEARch:FJUM
p:CONTrol
Jumps to the Control Field in the CAN FD bus signal search result. 5-165
:SERialbus<x>:CANFD:SEARch:FJUM
p:CRC
Jumps to the CRC Field in the CAN FD bus signal search result. 5-165
:SERialbus<x>:CANFD:SEARch:FJUM
p:DATA
Jumps to the Data Field in the CAN FD bus signal search result. 5-166
:SERialbus<x>:CANFD:SEARch:FJUM
p:IDENtifier
Jumps to the Identifier in the CAN FD bus signal search result. 5-166
:SERialbus<x>:CANFD:SEARch:FJUM
p:SOF
Jumps to the SOF in the CAN FD bus signal search result. 5-166
:SERialbus<x>:CANFD:SEARch:SELe
ct
Queries which detected point to display in the CAN FD bus signal search
zoom window and queries the zoom position of the detected point.
5-166
:SERialbus<x>:CANFD:SEARch:SELe
ct? MAXimum
Queries the number of detected points in the CAN FD bus signal search. 5-166
:SERialbus<x>:CANFD:SEARch:SET
up?
Queries all CAN FD bus signal search condition settings. 5-166
:SERialbus<x>:CANFD:SEARch:SETu
p:EFRame?
Queries all CAN FD bus signal search error settings. 5-166
:SERialbus<x>:CANFD:SEARch:SETu
p:EFRame:CRC
Sets or queries the CAN FD bus signal search CRC error setting. 5-166
:SERialbus<x>:CANFD:SEARch:SETu
p:EFRame:CRCEFactor?
Queries all CRC error factor settings for CAN FD bus signal searching. 5-166
5.1 List of Commands