YOKOGAWA DLM4038 - Page 60

5-27
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
Command Function Page
:SERialbus<x>:FLEXray:ANALyze?
Queries all FlexRay bus signal settings. 5-180
:SERialbus<x>:FLEXray[:ANALyze]
:SETup?
Queries all FlexRay bus signal analysis settings. 5-180
:SERialbus<x>:FLEXray[:ANALyze]
:SETup:BCHannel
Sets or queries the channel bus type for FlexRay bus signal analysis. 5-180
:SERialbus<x>:FLEXray[:ANALyze]
:SETup:BRATe
Sets or queries the FlexRay bus signal analysis bit rate (data transfer rate). 5-181
:SERialbus<x>:FLEXray[:ANALyze]
:SETup:SOURce
Sets or queries the source signal for FlexRay bus signal analysis. 5-181
:SERialbus<x>:FLEXray[:ANALyze]
:SETup:SPOint
Sets or queries the FlexRay bus signal sample point. 5-181
:SERialbus<x>:FLEXray:DETail?
Queries all FlexRay bus signal analysis result list settings. 5-181
:SERialbus<x>:FLEXray:DETail:DI
SPlay
Sets or queries the display mode for the FlexRay bus signal analysis result
list.
5-181
:SERialbus<x>:FLEXray:DETail:LI
ST:ITEM?
Queries all items that will be displayed in the FlexRay bus signal analysis
result list.
5-181
:SERialbus<x>:FLEXray:DETail:LI
ST:VALue?
Queries all of the data for the specified analysis number in the FlexRay bus
signal analysis result list.
5-181
:SERialbus<x>:FLEXray:SEARch?
Queries all FlexRay bus signal search settings. 5-181
:SERialbus<x>:FLEXray:SEARch:AB
ORt
Aborts the FlexRay bus signal search. 5-181
:SERialbus<x>:FLEXray:SEARch:EX
ECute
Executes a FlexRay bus signal search. 5-181
:SERialbus<x>:FLEXray:SEARch:FJ
UMp:CCOunt
Jumps to the cycle-count field in the FlexRay bus signal analysis results. 5-182
:SERialbus<x>:FLEXray:SEARch:FJ
UMp:CRC
Jumps to the CRC Field in the FlexRay bus signal analysis results. 5-182
:SERialbus<x>:FLEXray:SEARch:FJ
UMp:FRAMeid
Jumps to the frame ID field in the FlexRay bus signal analysis results. 5-182
:SERialbus<x>:FLEXray:SEARch:FJ
UMp:HCRC
Jumps to the Header CRC Field in the FlexRay bus signal analysis results. 5-182
:SERialbus<x>:FLEXray:SEARch:FJ
UMp:PLENgth
Jumps to the Payload Length Field in the FlexRay bus signal analysis
results.
5-182
:SERialbus<x>:FLEXray:SEARch:SE
Lect
Sets the detected-waveform number of the FlexRay bus signal search, or
queries the zoom location that corresponds to the number.
5-182
:SERialbus<x>:FLEXray:SEARch:SE
Tup?
Queries all FlexRay bus signal search condition settings. 5-182
:SERialbus<x>:FLEXray:SEARch:SE
Tup:ERRor?
Queries all FlexRay bus signal search error settings. 5-182
:SERialbus<x>:FLEXray:SEARch:SE
Tup:ERRor:BSS
Sets or queries the FlexRay bus signal search BSS error setting. 5-182
:SERialbus<x>:FLEXray:SEARch:SE
Tup:ERRor:CRC
Sets or queries the FlexRay bus signal search CRC error setting. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup:ERRor:FES
Sets or queries the FlexRay bus signal search FES error setting. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup:ERRor:HCRC
Sets or queries the FlexRay bus signal search Header CRC error setting. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup:IDData?
Queries all ID and data condition settings for FlexRay bus signal searching. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:CCOunt?
Queries all cycle-count settings for FlexRay bus signal searching. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:CCOunt:CONDition
Sets or queries the cycle-count data-condition settings for FlexRay bus
signal searching.
5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:CCOunt:COUNt<y>
Sets or queries a FlexRay bus signal-search cycle-count setting. 5-183
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:CCOunt:MODE
Sets or queries the cycle-count mode, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-184
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA?
Queries all ID and data condition settings for FlexRay bus signal searching. 5-184
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:BCOunt
Sets or queries the position for comparing data patterns, which is one of the
ID and data conditions, for FlexRay bus signal searching.
5-184
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:CONDition
Sets or queries the comparison condition, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-184
5.1 List of Commands