5-28
IM DLM4038-17EN
Command Function Page
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:DBYTe
Sets or queries the number of data bytes, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-184
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:DECimal<y>
Sets or queries a reference value, which is one of the ID and data conditions,
for FlexRay bus signal searching in decimal notation.
5-184
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:ENDian
Sets or queries the byte order of the reference values, which is one of the ID
and data conditions, for FlexRay bus signal searching.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:HEXa<y>
Sets a reference value, which is one of the ID and data conditions, for
FlexRay bus signal searching in hexadecimal notation.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:MODE
Sets or queries the data enable/disable condition, which is one of the ID and
data conditions, for FlexRay bus signal searching.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:MSBLsb
Sets or queries the MSB and LSB bits for the data, which is one of the ID
and data conditions, for FlexRay bus signal searching.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:PATTern<y>
Sets or queries the data value, which is one of the ID and data conditions, for
FlexRay bus signal searching in binary notation.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:PFORmat
Sets or queries the data input format, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-185
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:DATA:SIGN
Sets or queries whether a signed or unsigned data format will be used (this
is one of the ID and data conditions) for CAN bus signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:FID?
Queries all frame ID settings for the ID and data conditions for FlexRay bus
signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:FID:CONDition
Sets or queries the frame ID data condition, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:FID:ID<y>
Sets or queries the frame ID value, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:FID:MODE
Sets or queries the frame ID enable/disable condition, which is one of the ID
and data conditions, for FlexRay bus signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator?
Queries all indicator settings for the ID and data conditions for FlexRay bus
signal searching.
5-186
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator:MODE
Sets or queries the indicator enable/disable condition, which is one of the ID
and data conditions, for FlexRay bus signal searching.
5-187
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator:NFRame
Sets or queries the indicator null frame, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-187
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator:PPReamb
le
Sets or queries the indicator payload preamble, which is one of the ID and
data conditions, for FlexRay bus signal searching.
5-187
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator:STFRame
Sets or queries whether or not the indicator start frame, which is one of the
ID and data conditions, for FlexRay bus signal searching.
5-187
:SERialbus<x>:FLEXray:SEARch:SE
Tup[:IDData]:INDIcator:SYFRame
Sets or queries the indicator sync frame, which is one of the ID and data
conditions, for FlexRay bus signal searching.
5-187
:SERialbus<x>:FLEXray:SEARch:SE
Tup:MODE
Sets or queries the FlexRay bus signal search mode. 5-187
:SERialbus<x>:I2C?
Queries all I
2
C bus signal analysis and search settings. 5-187
:SERialbus<x>:I2C:ANALyze?
Queries all I
2
C bus signal analysis settings. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up?
Queries all I
2
C bus signal analysis bus settings. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up:CLOCk?
Queries all I
2
C bus signal analysis clock settings. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up:CLOCk:SOURce
Sets or queries the clock source for I
2
C bus signal analysis. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up:DATA?
Queries all I
2
C bus signal analysis data settings. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up:DATA:SOURce
Sets or queries the I
2
C bus signal data source. 5-188
:SERialbus<x>:I2C[:ANALyze]:SET
up:INCLuderw
Sets or queries the on/off status of the R/W address bit in I
2
C bus signal
analysis.
5-188
:SERialbus<x>:I2C:DETail?
Queries all I
2
C bus signal analysis result list settings. 5-188
:SERialbus<x>:I2C:DETail:DISPl
ay
Sets or queries the display mode for the I
2
C bus signal analysis result list. 5-188
:SERialbus<x>:I2C:DETail:LIST:I
TEM?
Queries all items that will be displayed in the I
2
C bus signal analysis result
list.
5-189
:SERialbus<x>:I2C:DETail:LIST:V
ALue?
Queries all of the data for the specified analysis number in the I
2
C bus signal
analysis result list.
5-189
:SERialbus<x>:I2C:SEARch?
Queries all I
2
C bus signal search settings. 5-189
:SERialbus<x>:I2C:SEARch:ABORt
Aborts the I
2
C bus signal search. 5-189
5.1 List of Commands
To Next Page
Loading...
