YOKOGAWA DLM4038 - Page 62

5-29
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
Command Function Page
:SERialbus<x>:I2C:SEARch:EXECu
te
Executes a I
2
C bus signal search. 5-189
:SERialbus<x>:I2C:SEARch:SELect
Sets which detected point to display in the I
2
C bus signal search zoom
window and queries the zoom position of the detected point.
5-189
:SERialbus<x>:I2C:SEARch:SELect?
MAXimum
Queries the number of detected points in the I
2
C bus signal search. 5-189
:SERialbus<x>:I2C:SEARch:SETup?
Queries all I
2
C bus signal search condition settings. 5-189
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess?
Queries all address pattern settings for I
2
C bus signal searching. 5-189
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess?
Queries all address pattern address settings for I
2
C bus signal searching. 5-189
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT10ADdress?
Queries all 10-bit address settings for I
2
C bus signal searching. 5-189
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT10ADdress:
HEXa
Sets the 10-bit address for I
2
C bus signal searching in hexadecimal notation. 5-189
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT10ADdress:
PATTern
Sets or queries the 10-bit address for I
2
C bus signal searching in binary
notation.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7ADdress?
Queries all 7-bit address settings for I
2
C bus signal searching. 5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess[:BIT7ADdress]
:HEXa
Sets the 7-bit address for I
2
C bus signal searching in hexadecimal notation. 5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess[:BIT7ADdress]
:PATTern
Sets or queries the 7-bit address for I
2
C bus signal searching in binary
notation.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub?
Queries all 7-bit + sub address settings for I
2
C bus signal searching. 5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:ADD
Ress?
Queries all 7-bit address settings for the 7-bit + sub address for I
2
C bus
signal searching.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:ADD
Ress:HEXa
Sets the 7-bit address for the 7-bit + sub address for I
2
C bus signal searching
in hexadecimal notation.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:ADD
Ress:PATTern
Sets or queries the 7-bit address for the 7-bit + sub address for I
2
C bus
signal searching in binary notation.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:SAD
Dress?
Queries all sub address settings for the 7-bit + sub address for I
2
C bus signal
searching.
5-190
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:SAD
Dress:HEXa
Sets the sub address for the 7-bit + sub address for I
2
C bus signal searching
in hexadecimal notation.
5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:BIT7APsub:SAD
Dress:PATTern
Sets or queries the sub address for the 7-bit + sub address for I
2
C bus signal
searching in binary notation.
5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:MODE
Sets or queries the address condition enable/disable mode for I
2
C bus signal
searching.
5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:PFORmat
Sets or queries the address input format, which is one of the address
conditions, for I
2
C bus signal searching.
5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:ADDRess:TYPE
Sets or queries the address type, which is one of the address conditions, for
I
2
C bus signal searching.
5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA?
Queries all address pattern data settings for I
2
C bus signal searching. 5-191
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:BCOunt
Sets or queries the position for comparing data patterns for I
2
C bus signal
searching.
5-192
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:BMODe
Sets or queries the on/off status of the position for comparing data patterns
for I
2
C bus signal searching.
5-192
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:CONDition
Sets or queries the data comparison condition (true or false) for I
2
C bus
signal searching.
5-192
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:DBYTe
Sets or queries the number of data bytes that will be compared for I
2
C bus
signal searching.
5-192
5.1 List of Commands