YOKOGAWA DLM4038 - Page 63

5-30
IM DLM4038-17EN
Command Function Page
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:HEXa<y>
Sets the data value, which is one of the data conditions, for I
2
C bus signal
searching in hexadecimal notation.
5-192
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:MODE
Sets or queries the data condition enable/disable mode for I
2
C bus signal
searching.
5-192
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:PATTern<y>
Sets or queries the data value, which is one of the data conditions, for I
2
C
bus signal searching in binary notation.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:ADDRess:DATA:PFORmat
Sets or queries the data input format, which is one of the data conditions, for
I
2
C bus signal searching.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:GENeralcall?
Queries all general call settings for I
2
C bus signal searching. 5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:GENeralcall:BIT7Maddress?
Queries all general call’s 7-bit master address settings for I
2
C bus signal
searching.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:GENeralcall:BIT7Maddress:HEXa
Sets the general call’s 7-bit master address for I
2
C bus signal searching in
hexadecimal notation.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:GENeralcall:BIT7Maddress:PATT
ern
Sets or queries the general call’s 7-bit master address for I
2
C bus signal
searching in binary notation.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:GENeralcall:SBYTe
Sets or queries the general call’s second byte type for I
2
C bus signal
searching.
5-193
:SERialbus<x>:I2C:SEARch[:SETup
]:MODE
Sets or queries the I
2
C bus signal search type. 5-194
:SERialbus<x>:I2C:SEARch[:SETup
]:NONack?
Queries all NON ACK ignore mode settings for I
2
C bus signal searching. 5-194
:SERialbus<x>:I2C:SEARch[:SETup
]:NONack:HSMode
Sets or queries whether or not NON ACK will be ignored in high-speed mode
for I
2
C bus signal searching.
5-194
:SERialbus<x>:I2C:SEARch[:SETup
]:NONack:READaccess
Sets or queries whether or not NON ACK will be ignored in read access
mode for I
2
C bus signal searching.
5-194
:SERialbus<x>:I2C:SEARch[:SETup
]:NONack:STARtbyte
Sets or queries whether or not NON ACK will be ignored in start bytes for I
2
C
bus signal searching.
5-194
:SERialbus<x>:LIN?
Queries all LIN bus signal analysis and search settings. 5-194
:SERialbus<x>:LIN:ANALyze?
Queries all LIN bus signal analysis settings. 5-194
:SERialbus<x>:LIN[:ANALyze]:SET
up?
Queries all LIN bus signal analysis bus settings. 5-194
:SERialbus<x>:LIN[:ANALyze]:SET
up:BRATe
Sets or queries the LIN bus signal analysis bit rate (data transfer rate). 5-194
:SERialbus<x>:LIN[:ANALyze]:SET
up:REVision
Sets or queries the LIN bus signal analysis revision number. 5-195
:SERialbus<x>:LIN[:ANALyze]:SET
up:SOURce
Sets or queries the LIN bus signal analysis source. 5-195
:SERialbus<x>:LIN[:ANALyze]:SET
up:SPOint
Sets or queries the LIN bus signal sample point. 5-195
:SERialbus<x>:LIN:DETail?
Queries all LIN bus signal analysis result list settings. 5-195
:SERialbus<x>:LIN:DETail:DISPl
ay
Sets or queries the display mode for the LIN bus signal analysis result list. 5-195
:SERialbus<x>:LIN:DETail:LIST:I
TEM?
Queries all items that will be displayed in the LIN bus signal analysis result
list.
5-195
:SERialbus<x>:LIN:DETail:LIST:V
ALue?
Queries all of the data for the specified analysis number in the LIN bus signal
analysis result list.
5-195
:SERialbus<x>:LIN:SEARch?
Queries all LIN bus signal search settings. 5-195
:SERialbus<x>:LIN:SEARch:ABORt
Aborts the LIN bus signal search. 5-195
:SERialbus<x>:LIN:SEARch:EXECu
te
Executes a LIN bus signal search. 5-195
:SERialbus<x>:LIN:SEARch:FJUMp:
BREak
Jumps to the break field in the LIN bus signal search result. 5-196
:SERialbus<x>:LIN:SEARch:FJUMp:
CSUM
Jumps to the checksum field in the LIN bus signal search result. 5-196
:SERialbus<x>:LIN:SEARch:FJUMp:
DATA
Jumps to the data field in the LIN bus signal search result. 5-196
:SERialbus<x>:LIN:SEARch:FJUMp:
IDENtifier
Jumps to the identifier field in the LIN bus signal search result. 5-196
:SERialbus<x>:LIN:SEARch:FJUMp:
SYNCh
Jumps to the sync field in the LIN bus signal search result. 5-196
:SERialbus<x>:LIN:SEARch:SELect
Sets which detected point to display in the LIN bus signal search zoom
window and queries the zoom position of the detected point.
5-196
5.1 List of Commands