YOKOGAWA DLM4038 - Page 64

5-31
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
Command Function Page
:SERialbus<x>:LIN:SEARch:SELect?
MAXimum
Queries the number of detected points in the LIN bus signal search. 5-196
:SERialbus<x>:LIN:SEARch:SETup?
Queries all LIN bus signal search condition settings. 5-196
:SERialbus<x>:LIN:SEARch:SETup:
ERRor?
Queries all LIN bus signal search error settings. 5-196
:SERialbus<x>:LIN:SEARch:SETup:
ERRor:CHECksum
Sets or queries the LIN bus signal search checksum error setting. 5-196
:SERialbus<x>:LIN:SEARch:SETup:
ERRor:FRAMing
Sets or queries the LIN bus signal search framing error setting. 5-196
:SERialbus<x>:LIN:SEARch:SETup:
ERRor:PARity
Sets or queries the LIN bus signal search parity error setting 5-197
:SERialbus<x>:LIN:SEARch:SETup:
ERRor:SYNCh
Sets or queries the LIN bus signal search synch error setting. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
ERRor:TIMeout
Sets or queries the LIN bus signal search timeout error setting. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
IDData?
Queries all ID and data condition settings for LIN bus signal searching. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA?
Queries all LIN bus signal search data settings. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:CONDition
Sets or queries the data conditions for LIN bus signal searching. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:DBYTe
Sets or queries the number of data bytes for LIN bus signal searching. 5-197
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:DECimal<y>
Sets or queries the data value for LIN bus signal searching in decimal
notation.
5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:ENDian
Sets or queries the data endian setting for LIN bus signal searching. 5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:HEXa<y>
Sets the data for LIN bus signal searching in hexadecimal notation. 5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:MODE
Sets or queries the data enable/disable condition for LIN bus signal
searching.
5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:MSBLsb
Sets or queries the data MSB and LSB bits for LIN bus signal searching. 5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:PATTern<y>
Sets or queries the data value for LIN bus signal searching in binary notation. 5-198
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:PFORmat
Sets or queries the input format, which is one of the data conditions, for LIN
bus signal searching.
5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:SIGN
Sets or queries whether signed or unsigned data format will be used, which
is one of the data conditions, for LIN bus signal searching.
5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier?
Queries all identifier settings for the ID and data conditions for LIN bus signal
searching.
5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier:ID?
Queries all LIN bus signal search ID settings. 5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier:ID:HEXa
Sets the ID for LIN bus signal searching in hexadecimal notation. 5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier:ID:MODE
Sets or queries the ID enable/disable condition for LIN bus signal searching. 5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier:ID:PATTern
Sets or queries the ID value for LIN bus signal searching in binary notation. 5-199
:SERialbus<x>:LIN:SEARch:SETup:
IDData:IDENtifier:PFORmat
Sets or queries the ID input format for LIN bus signal searching. 5-199
:SERialbus<x>:LIN:SEARch:SETup:
MODE
Sets or queries the LIN bus signal search mode setting. 5-200
:SERialbus<x>:PSI5?
Queries all PSI5 signal analysis and search settings. 5-200
:SERialbus<x>:PSI5:ANALyze?
Queries all PSI5 signal analysis settings. 5-200
:SERialbus<x>:PSI5[:ANALyze]:SE
Tup?
Queries all bus setup settings for PSI5 signal analysis. 5-200
:SERialbus<x>:PSI5[:ANALyze]:SE
Tup:DATA?
Queries all PSI5 signal analysis data signal settings. 5-200
:SERialbus<x>:PSI5[:ANALyze]:SE
Tup:DATA:BRATe
Sets or queries the PSI5 signal analysis bit rate (data transfer rate). 5-200
:SERialbus<x>:PSI5[:ANALyze]:SE
Tup:DATA:CTOLerance
Sets or queries the PSI5 signal analysis clock tolerance. 5-200
5.1 List of Commands