YOKOGAWA DLM4038 - Page 70

5-37
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
Command Function Page
:SERialbus<x>:SENT:TRENd<y>:CUR
Sor:DV:VALue?
Queries the vertical value between cursors on the SENT signal analysis
trend display.
5-220
:SERialbus<x>:SENT:TRENd<y>:CUR
Sor:MODE
Sets or queries the automated measurement mode of the SENT signal
analysis trend display.
5-220
:SERialbus<x>:SENT:TRENd<y>:CUR
Sor:POSition<z>
Sets or queries the position of the specified cursor on the SENT signal
analysis trend display.
5-220
:SERialbus<x>:SENT:TRENd<y>:CUR
Sor:T<z>:VALue?
Queries the time value at the specified cursor on the SENT signal analysis
trend display.
5-221
:SERialbus<x>:SENT:TRENd<y>:CUR
Sor:V<z>:VALue?
Queries the vertical value at the specified cursor on the SENT signal analysis
trend display.
5-221
:SERialbus<x>:SENT:TRENd<y>:DIS
Play
Sets or queries whether to show (ON) or hide (OFF) the SENT signal
analysis trend.
5-221
:SERialbus<x>:SENT:TRENd<y>:FCO
Ntrol
Sets or queries the frame control value on the SENT signal analysis trend
display.
5-221
:SERialbus<x>:SENT:TRENd<y>:HRA
Nge
Sets or queries the SENT signal analysis trend display source window. 5-221
:SERialbus<x>:SENT:TRENd<y>:SID
Sets or queries the slow channel ID of the SENT signal analysis trend display
in hexadecimal notation.
5-221
:SERialbus<x>:SENT:TRENd<y>:SOU
Rce
Sets or queries the SENT signal analysis trend display source channel. 5-221
:SERialbus<x>:SENT:TRENd<y>:UDA
Ta
Sets or queries the fast channel user-defined data of the SENT signal
analysis trend display.
5-222
:SERialbus<x>:SENT:TRENd<y>:VER
Tical
Sets or queries the vertical range of the SENT signal analysis trend display. 5-222
:SERialbus<x>:SENT:TRENd<y>:VTD
isplay
Sets or queries the on/off status of the VT waveform display on the SENT
signal analysis trend display.
5-222
:SERialbus<x>:SOURce?
Queries all analysis and search settings. 5-222
:SERialbus<x>:SOURce:{CHANnel<y
>|MATH<y>}?
Queries all source waveform settings. 5-222
:SERialbus<x>:SOURce:{CHANnel<y
>|MATH<y>}:HYSTeresis
Sets or queries a source waveform hysteresis. 5-222
:SERialbus<x>:SOURce:{CHANnel<y
>|MATH<y>}:LEVel
Sets or queries a source waveform level. 5-222
:SERialbus<x>:SPATtern?
Queries all user-defined bus signal analysis and search settings. 5-222
:SERialbus<x>:SPATtern:ANALyze?
Queries all user-defined bus signal analysis execution settings. 5-222
:SERialbus<x>:SPATtern[:ANALyze
]:SETup?
Queries all user-defined bus signal analysis settings. 5-222
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:BRATe
Sets or queries the bit rate for user-defined bus signal analysis. 5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CLOCk?
Queries all clock signal settings for user-defined bus signal analysis. 5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CLOCk:MODE
Sets or queries the clock signal enable or disable status for user-defined bus
signal analysis.
5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CLOCk:POLarity
Sets or queries the clock signal slope for user-defined bus signal analysis. 5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CLOCk:SOURce
Sets or queries the clock signal for user-defined bus signal analysis. 5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CS?
Queries all chip select signal settings for user-defined bus signal analysis. 5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CS:ACTive
Sets or queries the chip select signal active state for user-defined bus signal
analysis.
5-223
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:CS:SOURce
Sets or queries the chip select signal for user-defined bus signal analysis. 5-224
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:DATA?
Queries all data signal settings for user-defined bus signal analysis. 5-224
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:DATA:ACTive
Sets or queries the data signal active state for user-defined bus signal
analysis.
5-224
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:DATA:SOURce
Sets or queries the data signal for user-defined bus signal analysis. 5-224
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:LATCh?
Queries all latch signal settings for user-defined bus signal analysis. 5-224
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:LATCh:POLarity
Sets or queries the latch signal slope for user-defined bus signal analysis. 5-224
5.1 List of Commands