YOKOGAWA DLM4038 - Page 71

5-38
IM DLM4038-17EN
Command Function Page
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:LATCh:SOURce
Sets or queries the latch signal for user-defined bus signal analysis. 5-225
:SERialbus<x>:SPATtern[:ANALyze
]:SETup:SPOint
Sets or queries the analysis start point for user-defined bus signal analysis. 5-225
:SERialbus<x>:SPATtern:SEARch?
Queries all user-defined bus signal search settings. 5-225
:SERialbus<x>:SPATtern:SEARch:A
BORt
Aborts the user-defined bus signal search. 5-225
:SERialbus<x>:SPATtern:SEARch:E
XECute
Executes a user-defined bus signal search. 5-225
:SERialbus<x>:SPATtern:SEARch:S
ELect
Sets which detected point to display in the user-defined bus signal search
zoom window and queries the zoom position of the detected point.
5-225
:SERialbus<x>:SPATtern:SEARch:S
ELect? MAXimum
Queries the number of detected points in the user-defined bus signal search. 5-225
:SERialbus<x>:SPATtern:SEARch:S
ETup?
Queries all user-defined bus signal search condition settings. 5-225
:SERialbus<x>:SPATtern:SEARch:S
ETup:BITSize
Sets or queries the bit length setting for user-defined bus signal analysis. 5-225
:SERialbus<x>:SPATtern:SEARch:S
ETup:HEXa
Sets or queries the data condition for user-defined bus signal searching in
hexadecimal notation.
5-226
:SERialbus<x>:SPATtern:SEARch:S
ETup:PATTern
Sets or queries the data condition for user-defined bus signal searching in
binary notation.
5-226
:SERialbus<x>:SPATtern:SEARch:S
ETup:PFORmat
Sets or queries the input format, which is one of the data conditions, for user-
defined bus signal searching.
5-226
:SERialbus<x>:SPI?
Queries all SPI bus signal analysis and search settings. 5-226
:SERialbus<x>:SPI:ANALyze?
Queries all SPI bus signal analysis settings. 5-226
:SERialbus<x>:SPI[:ANALyze]:SET
up?
Queries all SPI bus signal analysis bus settings. 5-226
:SERialbus<x>:SPI[:ANALyze]:SET
up:BITorder
Sets or queries the bit order of the SPI bus signal analysis data. 5-226
:SERialbus<x>:SPI[:ANALyze]:SET
up:CLOCk?
Queries all clock signal settings for SPI bus signal analysis. 5-226
:SERialbus<x>:SPI[:ANALyze]:SET
up:CLOCk:POLarity
Sets or queries the clock signal slope for SPI bus signal analysis. 5-226
:SERialbus<x>:SPI[:ANALyze]:SET
up:CLOCk:SOURce
Sets or queries the clock signal for SPI bus signal analysis 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:CS?
Queries all chip select signal settings for SPI bus signal analysis. 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:CS:ACTive
Sets or queries the chip select signal active state for SPI bus signal analysis. 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:CS:SOURce
Sets or queries the chip select signal for SPI bus signal analysis. 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:DATA<y>?
Queries all data signal settings for SPI bus signal analysis. 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:DATA<y>:SOURce
Sets or queries the data signal for SPI bus signal analysis. 5-227
:SERialbus<x>:SPI[:ANALyze]:SET
up:FIELd
Sets or queries the data field size for SPI bus signal analysis. 5-228
:SERialbus<x>:SPI[:ANALyze]:SET
up:GROuping
Sets or queries the on/off status of grouping for SPI bus signal analysis when
there is no chip select signal.
5-228
:SERialbus<x>:SPI[:ANALyze]:SET
up:ITIMe
Sets or queries the idle time for SPI bus signal analysis when there is no
chip select signal.
5-228
:SERialbus<x>:SPI[:ANALyze]:SET
up:MODE
Sets or queries the data signal wiring system (three-wire or four-wire) for SPI
bus signal analysis.
5-228
:SERialbus<x>:SPI[:ANALyze]:SET
up:MSBLsb
Sets or queries the data MSB and LSB bits for SPI bus signal analysis. 5-228
:SERialbus<x>:SPI:DETail?
Queries all SPI bus signal analysis result list settings. 5-228
:SERialbus<x>:SPI:DETail:DISPl
ay
Sets or queries the display mode for the SPI bus signal analysis result list. 5-228
:SERialbus<x>:SPI:DETail:LIST:I
TEM?
Queries all items that will be displayed in the SPI bus signal analysis result
list.
5-229
:SERialbus<x>:SPI:DETail:LIST:V
ALue?
Queries all of the data for the specified analysis number in the SPI bus signal
analysis result list.
5-229
:SERialbus<x>:SPI:SEARch?
Queries all SPI bus signal search settings. 5-229
5.1 List of Commands