Need help?Do you have a question about the ADPRO iFT Series and is the answer not in the manual?
General| Category | Network Hardware |
|---|---|
| Wavelength | 1310nm or 1550nm (Single-mode), 850nm (Multi-mode) |
| Video Compression | H.264, MJPEG |
| Network Interface | 10/100/1000 Mbps Ethernet |
| Power Supply | 12V DC or PoE |
| Fiber Type | Single-mode or Multi-mode |
| Transmission Distance | Up to 2km (Multi-mode) |
| Storage | Supports external storage via NAS or SAN |
Information on available iFT and iFT-E models, and their IP channel/analytics capabilities.
Overview of required and optional licenses for XO devices, including system and IP channel licenses.
Information on obtaining and installing software updates for XO devices via the Xchange tool.
Guidance on using reference numbers for ordering parts and identifying correct components.
Guidance on calculating required hard disk space using Honeywell's calculator and system requirements.
Instructions for adding or replacing hard disks, including part numbers for ordering.
Procedure for reusing used hard disks, including formatting and potential lockdown mode issues.
Methods to retrieve hard disk information and identify faulty disks using Telnet or XO client.
Material required and steps for installing the first hard disk in the iFT device.
Material and steps for installing a second hard disk, including bracket information.
Material and steps for installing a third hard disk in iFT devices with extra mounting holes.
Material and steps for installing third/fourth disks in iFT-E devices (model 63xxxxxx).
Information and configuration steps for RAID 1 mirroring for data redundancy.
Instructions for remotely formatting hard disks using the XO client or hardware configuration tool.
Description of front panel LEDs: Power (Green), Fault (Yellow), and Activity (Blue).
Information about the PH10LU motherboard used in the iFT Series.
Steps to configure BIOS settings for optimal system performance and compatibility.
Overview of motherboard connectors at the rear of the device, including USB port details.
Instructions and warnings regarding motherboard replacement, including license implications.
Guidance on replacing the motherboard battery and where to find further instructions.
Details on the separate IP network connections required for IP cameras and client communication.
Description of the internal Main I/O (MIO) card features, including inputs and outputs.
Overview and connection procedures for the Main I/O card inputs and outputs.
Guidance on configuring MIO card inputs/outputs and updating its firmware.
Introduction to XO I/O Interface USB modules for extra inputs/outputs and their restrictions.
Steps to enable Technician user and generate a PIN for accessing the hardware configuration tool.
Procedure for connecting and mapping XO I/O Interface USB modules using the hardware configuration tool.
Procedure for resetting USB port numbering to defaults after removing XO I/O Interface USB modules.
Information on Network I/O units for expanding inputs/outputs, including power and extension options.
How to connect a monitor for live viewing, system info, and accessing the XO Installer menu.
Connecting PSTN/ISDN or 3G/4G modems to the XO device via USB port 1.
Using the Huawei E8372 wingle for 4G connection, including PC preparation and XO client setup.
Details on audio input availability from cameras and IP audio devices, and recording options.
Configuration and setup for talkback audio functionality using various audio units.
Minimum firmware version required for PIR alarm processing and features.
Options for connecting PIR detectors to the XO device, including RS-485 and IP module methods.
PIR detector addressing requirements based on firmware version and uniqueness.
Connecting PIR detectors directly to the MIO card via RS-485 bus.
Connecting PIR detectors using a USB-to-RS-485 distribution unit and its configuration.
Connecting PIR detectors using a USB-to-Serial-Port RS-485 converter.
Connecting PIR detectors via the IFM-485-ST interface module to the XO device USB port.
Connecting PIR detectors using IP modules and setting them up for XO client communication.
Estimated power consumption based on components and system load, with example values.
Methods to find the XO device's IP address using the XO client or the welcome screen.
Overview of generating and capturing log files and reports for troubleshooting.
Procedure for enabling and retrieving log files via the device's IP address and web browser.
Viewing server reports via the internet browser by accessing IP address with /report.php.
Description of available web pages for device management, logging, and network analysis.
Basic maintenance guidelines, emphasizing keeping the device dust-free and cleaning procedures.
Procedure for performing a full device reset by flashing the iFT image file to the DOM.
Steps to restore system license and application licenses after a full device reset.
Explanation of the 8-digit product number structure for iFT Series devices and their options.
Supplier's declaration of conformity with EMC and alarm system standards.
Alphabetical list of abbreviations used in the manual with their full meanings.
To Next Page
