AIRTRONICS MT-S - Page 47

47
TR
MT- S
2.4GHZ FH4T RADIO SYSTEM USER'S GUIDE
Telemetry System with Sanwa Synchronized Link Support
Stopping the Lap Timer:
1) To stop the Lap Timer, press and HOLD Auxiliary Switch Sw1 for 3 seconds. An audible double-tone will sound indicating the
Lap Timer is stopped and the Cumulative Time will be displayed on the STATUS screen and in the TIMER menu.
The Cumulative Time cannot be manually cleared. It will be automatically cleared when the Lap Timer is put in
Stand-by again.
Starting the Lap Timer:
1) In the default configuration, Auxiliary Switch Sw1 controls the Timer function (the Timer function can only be Assigned to
Auxiliary Switch Sw1). Press and HOLD Auxiliary Switch Sw1 for 3 seconds. An audible double-tone will sound, the TIMER
screen will appear for a short time and LAP will flash on the STATUS screen indicating the Lap Timer is in Stand-by.
To start the Lap Timer, press Auxiliary Switch Sw1 a second time or pull the
Throttle Trigger. An audible double-tone
will sound and the Lap Timer will start
counting Up.
After the Lap Timer is started, pressing
Auxiliary Switch Sw1 a second time will
store the first Lap Time, then begin counting
a second Lap Time. Each time you press
Auxiliary Switch Sw1, an audible tone
sounds, the previous Lap Time is stored, a new Lap Time begins and the current Lap Time is displayed momentarily.
TIMER MENU
LAP MENU

LAP TIMER

TIMER
TIMER SET INT setting range is --:-- . -- to 99:59.99. The default setting is --:-- . -- (OFF). When the Lap Timer is counting Up,
an audible double-tone will sound each time the Lap Timer reaches the Interval Timer value. For example, if you set the
Interval Timer for 01:30.00, an audible double-tone will sound every 1 minute and 30 seconds.
5) To set the Interval Timer 1/100th Seconds value, press the ENTER key, then press the
DOWN key to highlight 00. Press the ENTER key a second time, then press the UP
or DOWN keys to set the desired Interval Timer 1/100th Seconds value.
Setting the Interval Timer (Target Time), Continued:
4) To set the Interval Timer Seconds value, press the ENTER key, then press the DOWN key to highlight 00. Press the ENTER
key a second time, then press the UP or DOWN keys to set the desired Interval Timer Seconds value.
Setting the Alarm (Goal Time):
1) From within the TIMER menu, press the DOWN key to highlight ALRM 05.
2) Press the ENTER key, then press the UP or DOWN keys to set the desired Alarm
Minutes value.
3) To set the Alarm Seconds value, press the ENTER key, then press the DOWN key to
highlight 00. Press the ENTER key a second time, then press the UP or DOWN keys
to set the desired Alarm Seconds value.
TIMER SET ALRM setting range is 00:00 to 99:59. The default setting is 5:00 minutes. An audible tone will sound in 1 second
intervals 5 seconds before reaching the Goal Time. When the Goal Time is reached, a long audible tone will sound.
Choosing the Key Option (Key Assign Function):
Inthedefaultconfiguration,theTimerfunctioniscontrolledbyAuxiliarySwitchSw1.TheKeyoptionisashortcuttotheKEY
ASSIGN menu, which allows you to Assign the Timer function to Auxiliary Switch Sw1 if another function has been Assigned to
it. The Timer function can only be Assigned to Auxiliary Switch Sw1.
1) PresstheENTERkey,thenpresstheUPorDOWNkeystohighlightKEY.
2) PresstheENTERkeytoopentheKEYASSIGNmenu,thenAssignTIMERtoAuxiliary
SwitchSw1.Formoreinformation,seetheKEYASSIGNMenusectiononpages56
through 60.