AIRTRONICS MT-S - Page 58

58
MT- S
2.4GHZ FH4T RADIO SYSTEM USER'S GUIDE
TR
Telemetry System with Sanwa Synchronized Link Support
TWEAK1andTWEAK2cannotbecontrolledatthesametime.Youcancontrolonlyoneortheotheratanyonetime.
KEY ASSIGN MENU

KEY ASSIGNMENTS

SYSTEM
Changing the Switch Mode:
Some functions allow you to change how Auxiliary Switch Sw1 operates. The following Switch Modes are available:
TOGGLE - When selected, press Auxiliary Switch Sw1 to turn the function ON and press Auxiliary Switch Sw1 a second time
to turn the function OFF.
PUSH - When selected, press and HOLD Auxiliary Switch Sw1 to turn the function ON. When Auxiliary Switch Sw1 is
released, the function will be turned OFF.
1) Fromwithin the KEY ASSIGNSWmenu,press the UP or DOWNkeysto highlight
MODE for Auxiliary Switch Sw1.
2) Press the ENTER key, then press the UP or DOWN keys to choose the desired Switch
Mode setting, either TOGGLE or PUSH for the selected Auxiliary Switch Sw1 function.
The Switch Mode can only be changed for Auxiliary Switch Sw1 and it cannot be changed for all functions. When
MODE ------ is displayed, Auxiliary Switch Sw1 will act as if it were in Toggle Mode.
Changing the Tweak1 and Tweak2 Values:
The Tweak1 and Tweak2 values determine how far and in which direction Auxiliary Switch Sw3 controls the function Assigned
to it, regardless if Auxiliary Switch Sw3 is controlling a servo, such as Auxiliary 2 (Channel 4) or a function parameter, such as
CUR-R-ST (Curve-Rate-Steering). For example, if you Assign AUX2 to Auxiliary Switch Sw3 and adjust the Tweak values to +50
and -50, the Auxiliary 2 (Channel 4) servo will travel 50% in one direction when Auxiliary Switch Sw3 is moved Forward and
travel 50% in the other direction when Auxiliary Switch Sw3 is moved Backward. Alternately, if you Assign CUR-R-ST to Auxiliary
Switch Sw3 and adjust the Tweak values to -25 and -50, you can change Steering Curve Rate from 0 to -20 to -50 by simply
moving Auxiliary Switch Sw3.
The Neutral position of Auxiliary Switch Sw3 can be changed from Position 1 to Position 2 to suit the programmed function and
your specific requirements.
TWEAK1 - When selected, Position 1 will be Neutral and Position 2 and Position 3 will be End Points.
TWEAK2 - When selected, Position 2 will be Neutral and Position 1 and Position 3 will be End Points.
Neutral
P1
P1
Neutral
P3
P3
TWEAK1
TWEAK2
1 2 3
1) Fromwithin the KEY ASSIGNSWmenu,press the UP or DOWNkeysto highlight
MODE TWEAK1 (or TWEAK2).
2) Press the ENTER key, then press the UP or DOWN keys to choose either TWEAK1 or
TWEAK2. Which value you choose will determine how Auxiliary Switch Sw3 functions,
as described above.
3) Press the ENTER key, then press the UP or DOWN keys to choose the desired
Position Tweak value you want to change, either TWEAK1
2
or
3
, or TWEAK2
1
or
3
. Increasing the Tweak value will Increase travel in the High Side direction and
Decreasing the Tweak value will Decrease travel in the High Side direction. Using a
Negative value will change the direction of travel.
4) Press the ENTER key, then repeat step 3 to change the Tweak value for the second
Position.
KEYASSIGNSWTWEAKsettingrangeis-100to+100.ThedefaultsettingforTWEAK1Position2is+100andthedefault
setting for TWEAK2 Position is -100. The default setting for TWEAK2 Position 1 is +100 and the default setting for TWEAK2
Position 3 is -100.
1 2 3