Allen-Bradley ClutchBrake PLC-5 Series - Page 149

Troubleshooting with Fault Codes, Operator Prompts, and Snapshot Status Bits C–7
Publication 65566.5.1 - October 1996
Prompts Associated with Processor A
B169/ Suggested Message Cause of the Prompt Condition Effect of Prompt Condition How to Correct the Condition
000 Spare
001 EStop actuated Estop button was pressed, or
Estop circuit failed.
CRM and seal relays opened. Release Estop btn. Press control
power and C/B power reset btns.
002004 Spare
005 Software inch mode enabled You pressed an inch button when
software inch mode bit was set
Hardware inch buttons void
when this bit is set.
Release hardware inch buttons.
006 Software inch mode is not
enabled.
Inch mode selected but software inch
mode bit is not set.
Valve outputs turn OFF. Set the software inch mode bit.
007 Downstroke stopped by software. Permit downstroke bit was reset while
the press was in downstroke.
Valve outputs turn OFF. Set the permit downstroke bit, and
inch the press to neartop position.
008 Upstroke stopped by software. Permit upstroke bit was reset while the
press was in upstroke.
Valve outputs turn OFF. Set the permit upstroke bit, and
inch the press to neartop position.
009 Permit start is not enabled. The permit start bit is not set. Press will not start in
single or continuous mode.
Set the permit start bit.
010 Permit run is not enabled. The permit run bit is not set. Valve outputs turn OFF,
or will not energized.
Set the permit run bit, and
inch the press to neartop position.
011012 Spare
013 Main motor is not running forward. Main motor not running forward in
single or continuous mode.
Valve outputs turn OFF. Start the main motor (forward).
014 C/B power is not reset. Seal relay is not closed. Valve outputs remain OFF. Clear faults. Press control power
and C/B power reset buttons.
015 Press is not in neartop position. Press is not in neartop position. You cannot stroke in single or
continuous mode.
Inch the press to neartop position.
016 All run buttons are not released. The press has stopped and all run
buttons are not released.
You cannot start the press. Release all run buttons.
017 Release inch buttons. The press has stopped and inch
buttons are not released.
None Release inch buttons.
018 Cycle start bit
has not been toggled.
The cycle start bit
has not been toggled
Press will not cycle in
automatic singlestroke mode
Toggle the cycle start bit.
019 Software stopontop is enabled. The stopontop bit is set. The press will complete the
cycle and stop at top.
None
020 Stopontop button is pressed. Stopontop button is pressed. The press will complete the
cycle and stop at top.
None
021 Continuous mode not armed. You did not press the arm continuous
button.
You cannot start the press in
continuous mode.
Press the arm continuous button.
022 Release inch buttons You did not release inch buttons after
reaching the top.
You cannot start the press
until you release the buttons.
Release the inch buttons.
023 Downstroke Disabled. Permit downstroke bit should be
set when starting the press.
You cannot start the press in
single or continuous mode.
Set the permit downstroke bit.
024 Spare
025 Proc. B not requesting inch mode. Processor B not requesting inch mode You cannot inch. Check remote I/O wiring.
026 Proc. B not engaging inch mode. Processor B not engaging inch mode. You cannot inch. Check remote I/O wiring.
027 Proc. B not engaging single mode. Processor B not engaging single mode You cannot start single stroke Check remote I/O wiring.
028 Proc. B not requesting arm contin. Processor B not requesting arm contin. You cannot start continuous. Check remote I/O wiring.
029 Proc. B not engaging contin mode. Processor B not engaging contin mode You cannot start continuous. Check remote I/O wiring.
030078 Spare
079 Processor A or B detected a fault. Processor A or B detected a fault. See fault table in Appendix C. See fault table.