Ametek Chatillon CS1100 - 21 Spare Parts Kits

135 pages

To Next Page

To Previous Page

21.0 SPARE PARTS

KITS

SPK-CS225 Sheet A

126 CS User Manual

Main Page

Default Chapter7
- Table of Contents7
1 Introduction11
- Safety12
- Electrical Safety12
- Operational Precautions13
2 Installation14
- Unpacking14
- Setting up Your Force Tester14
- Voltage Selection and Fuses15
- Control Console and Load Cell Cables16
- Mounting the Control Console16
- Connecting the Control Console Power Cable16
- Connecting the Control Console Usb Cable17
- Connecting the Load Cell External Cable17
- On-Off Switch17
- Emergency Stop Switch18
- Load Cells18
3 Initial Configuration19
- General19
- Initial Log-In19
- Languages21
- Date and Time27
- Screen Saver and Power Options27
- Usb Printer28
- Company Logo on Printed Reports29
- Network Connection29
- Windows Password29
- Touch Screen Calibration30
- Exiting Windows to Start the Dedicated Program30
4 Dedicated Program Configuration31
- Log-In and the Home Screen31
- User Settings32
- Setting Default Units33
- Changing the Safety Settings34
- Grip Protection34
- Pinch Load35
- Slow Jog Speed36
- Load Cell Calibration Interval36
- Communications36
- Overloads36
- Returning to the Home Screen36
- Changing Operator36
- Jog Panel38
- Turning off the Cs Force Tester39
5 Preparing the Force Tester40
- Fitting a Load Cell40
- T Slot Table40
- Lower Anchor Pin41
- Limit Stops42
6 Defining a Test44
- Notes44
7 Single Stage Test Without Saving Data45
- Basic Settings Screen45
- Test Limits Screen47
- Export Settings Screen49
- Displaying the Test Screen49
8 Defining a Compression or Tension Test51
- Creating a Compression Test File51
- Creating a Tension Test File51
- Test File51
- Basic Settings Screen51
- Test Limits Screen54
- Question Screen56
- Test Results Screen56
- Archive and Export Settings Screen59
- Displaying the Test Graph Screen60
9 Defining a Multi-Action Test61
- Creating a Multi-Action Test File61
- Basic Settings Screen61
- Select Next Stage Screen64
- Create a Tension Stage65
- Create a Cycle Test67
- Create a Compression Stage69
- Create a Hold Load Stage69
- Create a Hold Extension Stage69
- Create a Zero Stage70
- Create a User Input Stage70
- Editing or Deleting a Stage71
- Adding a Stage71
- Test Results Screen72
- Archive and Export Settings Screen76
- Displaying the Test Graph Screen77
10 Using the Force Tester78
- Performing a Test78
- Markers and Notes84
- Printing and Exporting Graph Data85
- Data Table and Statistics87
- Printing and Exporting Data Table and Statistics89
- Test Notes91
- Loading a Saved Test File91
- Favorites Feature95
- Test File Maintenance97
- Copy a Test97
- Edit a Test97
- Delete a Test98
- Export a Test98
- Install a Test98
11 Distance Compensation99
- General99
- Creating a New Distance Compensation99
12 Height Mode102
- Creating a Height Mode Test102
- Performing a Height Mode Test106
13 Load Cells109
- General Precautions109
- Additional Load Cells110
- Load Cell Resolution110
14 Installation Notes111
- Splinter Shield111
- Securing to the Workbench112
15 Error Conditions113
16 Cleaning and Maintenance114
- Cleaning External Finish and Trim114
- Maintenance114
17 Communications115
- Configuring the Communications115
- Using the Communications116
- Ascii Commands117
- Ascii Commands to Drive the Force Tester117
- List of All Ascii Commands118
18 Technical Specifications123
- Technical Specification Cs225123
- Technical Specification Cs1100123
- 19 Overall Dimensions124
20 Rohs TABLES125
21 Spare Parts Kits127

Ametek Chatillon CS1100 - 21 Spare Parts Kits

Table of Contents

Related product manuals