Asante 1012 - User Manual

Questions and Answers

M
michellehuffmanAug 14, 2025
How to improve degraded network performance on Asante Switch?
- K
  kellyjenniferAug 14, 2025
  To address degraded network performance with your Asante Switch, first ensure you're using solid conductor wire, not stranded. Check for electrical interference from nearby high-powered machinery; move the machinery away or use more shielded cables, and ensure the building is properly earth-grounded. Also, verify that all physical connections are secure and properly terminated, using well-built cables and keeping them away from high-traffic areas to prevent damage.
B
Brandon LarsonAug 17, 2025
What to do if certain devices cannot communicate over the network with Asante Switch?
- B
  Brittney BushAug 17, 2025
  If certain devices are unable to communicate over the network with your Asante Switch, first check if the device supports Link Integrity testing (is pre-10BaseT); if so, disable Link Integrity test on the port to that device. Also, verify the network interface card hardware configuration, port settings, and Link Integrity. Run card diagnostics using the diagnostic software provided by the card manufacturer. Check the network operating system and software for compatibility and corruption, reinstalling or restarting as necessary. Ensure that proper application software is running on the workstation to provide connection and that interface software is properly configured.
M
Michael WoodwardAug 20, 2025
What to do if unable to establish link on Asante Switch?
- S
  stonelisaAug 21, 2025
  If you're unable to establish a link with your Asante Switch, ensure that all physical connections are in place, tightly attached, properly terminated, and connecting the appropriate devices. Also, check for loopback at a device connection or between hubs if wiring has recently been changed.
M
Mr. David TorresAug 25, 2025
How to disable Link Integrity on Asante 1012?
- E
  Eric PetersonAug 25, 2025
  If Link Integrity is enabled on a port connected to a pre-10Base-T device on your Asante Switch, disable Link Integrity on that port through AsantéView (Port Control window) or a local terminal.
S
Shelly CainAug 27, 2025
How to prevent network performance degradation on Asante 1012?
- J
  Jasmin RamirezAug 27, 2025
  To address general network performance degradation or abnormal statistical indications with your Asante Switch, plan network usage to avoid bursts of traffic.
E
Emily DavisAug 30, 2025
What to do if network doesn't work after changing Asante 1012 configuration?
- Z
  zbauerAug 30, 2025
  If part of the network stops working after changing the hub configuration on your Asante Switch, restore the hub to its initial factory settings. Then, make changes one at a time, checking network performance after each change.
O
oconnoranneSep 3, 2025
What to do if workstations disrupt communication on Asante 1012?
- S
  Steven NovakSep 3, 2025
  If other workstations connected to the hub are disrupting communication of workstations being brought up on your Asante Switch, remove the disrupting workstations, or disable (partition) their links through AsantéView (Port Control window) or a local terminal.
B
Bradley NelsonSep 6, 2025
How to run hub diagnostics on Asante 1012?
- K
  Kimberly BrownSep 6, 2025
  To run hub diagnostics for miscellaneous problems with your Asante Switch, reset the hub using a narrow tool (or paper clip) to push the reset button. This will not affect traffic.
M
Michelle BlakeSep 9, 2025
Why is there no communication through AUI port on Asante 1012 Switch?
- A
  andersonnicholasSep 10, 2025
  If there is no communication through the AUI port on your Asante Switch, check the connections, continuity, and impedance of the AUI cable.