Azbil MagneW FLEX+ User Manual

Table of Contents
Chapter 1 : Introduction
1.1 : Principle of operation ......................................................................................... 1-1
1.2 : System operation ............................................................................................... 1-2
1.2.1: Integral type ........................................................................................................ 1-2
1.2.2: Remote type ........................................................................................................ 1-3
1.3 : Main components .............................................................................................. 1-4
1.3.1: Wafer type detector ............................................................................................. 1-5
1.3.2: Flange type detector ........................................................................................... 1-6
1.3.3: Union / Hose / Clamp type detector .................................................................... 1-7
1.3.4: Sanitary type detector ......................................................................................... 1-8
1.3.5: Detector terminal box .......................................................................................... 1-9
1.3.6: Approval of this device ........................................................................................ 1-10
Chapter 2 : Installation
2.1 : Unpacking .......................................................................................................... 2-1
2.1.1: Verifying specications ........................................................................................ 2-1
2.2 : Storage .............................................................................................................. 2-2
2.3 : Site selection ..................................................................................................... 2-3
2.3.1: Detector position ................................................................................................. 2-4
2.3.2: Changing the position of the terminal box ........................................................... 2-5
2.4 : Installing a wafer detector .................................................................................. 2-6
2.4.1: Determining the fastening torque ........................................................................ 2-7
2.4.2: Selecting the ange shape .................................................................................. 2-7
2.4.3: Necessary parts .................................................................................................. 2-9
2.4.4: Selecting an installation method ......................................................................... 2-12
2.4.5: Installation on a horizontal pipe ........................................................................... 2-13
2.4.6: Installation on a vertical pipe ............................................................................... 2-14
2.4.7: Installation on a metal pipe using SUS grounding ring material .......................... 2-15
2.4.8: Installation on a metal pipe using non-SUS grounding ring material .................. 2-16
2.4.9: Installation on a PVC pipe using SUS grounding ring material ........................... 2-19
2.4.10: Installation on a PVC pipe using non-SUS grounding ring material .................. 2-22
2.5 : Installing a anged detector ............................................................................... 2-25
2.5.1: Determining the fastening torque ........................................................................ 2-26
2.5.2: Necessary parts .................................................................................................. 2-31
2.5.3: Selecting an installation method ......................................................................... 2-32
2.5.4: Installation on a metal pipe using SUS grounding ring material .......................... 2-33
2.5.5: Installation on a metal pipe using non-SUS grounding ring material .................. 2-34
2.5.6: Installation on a PVC pipe using SUS grounding ring material ........................... 2-35
2.5.7: Installation on a PVC pipe using non-SUS grounding ring material .................... 2-39
2.6 : Installing a Union / Hose / Clamp Detector ........................................................ 2-43
2.6.1: Installation of Union and Hose assemblies basic installation method ................. 2-43
2.6.2: Installation of ISO-clamp/ Tri-clamp assembles basic installation method ......... 2-44
2.7 : Wiring the detector ............................................................................................. 2-46
2.7.1: Connecting the detector and converter (Remote models) .................................. 2-46
2.7.2: Grounding the detector (Remote models) ........................................................... 2-47
2.7.3: Installing the dedicated cable .............................................................................. 2-47
2.8 : Troubleshooting and maintenance .................................................................... 2-56

Azbil MagneW FLEX+ Specifications

General

Brand	Azbil
Model	MagneW FLEX+
Category	Measuring Instruments
Language	English