System manual Coronis 5MP 83
Setting the Resolution of Your CORONIS Display Panel withSetting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel withSetting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with
DualView enabledDualView enabled
DualView enabledDualView enabled
DualView enabled
Once you have completed the installation of the separate screens with
DualView, you need to set the resolution for each display. Both
screens of each display controller cannot be enabled at the same time
unless their display properties match.
1. To set the resolution for your CORONIS display panel(s) under
DualView, right click on the desktop and select
“Properties”“Properties”
“Properties”“Properties”
“Properties”.
2. Select the
“Settings”“Settings”
“Settings”“Settings”
“Settings” tab (see figure 58on the next page). Now
select the
rectrect
rectrect
rect
angleangle
angleangle
angle that represents the first CORONIS display
attached to the BarcoMed Display Controller you are working with.
SPECIALSPECIAL
SPECIALSPECIAL
SPECIAL
NOTE: NOTE:
NOTE: NOTE:
NOTE: If you are using the VGA capabilities of your
BarcoMed Display Controller, the resolution for the first display will
still be set to a VGA resolution of “640 x 480” pixels. If the
BarcoMed Display Controller is not running VGA, the display may
not be enabled yet. To enable the device
checkcheck
checkcheck
check the
“Extend my“Extend my
“Extend my“Extend my
“Extend my
WW
WW
W
indows desktop onto this monitor”indows desktop onto this monitor”
indows desktop onto this monitor”indows desktop onto this monitor”
indows desktop onto this monitor” checkbox. Do not click the
“Apply”“Apply”
“Apply”“Apply”
“Apply” button at this time.
If necessary detach the second display of the BarcoMed Display
Controller you are working with by right clicking on the rectangle
that represents it and deselect
“Att“Att
“Att“Att
“Att
ached”ached”
ached”ached”
ached”. Click the
“Apply”“Apply”
“Apply”“Apply”
“Apply”
button.
Note:Note:
Note:Note:
Note: Since Windows 2000 will not let you detach the primary
display, you may need to temporarily make another display the
primary display.
3. For the display which is still attached click on the
“Advanced”“Advanced”
“Advanced”“Advanced”
“Advanced”
Button.
4. Select the
“Adapter”“Adapter”
“Adapter”“Adapter”
“Adapter” tab and then click on the
“List “List
“List “List
“List
All Modes…”All Modes…”
All Modes…”All Modes…”
All Modes…”
button. Select the resolution and refresh rate that your CORONIS
display panel supports from the dialog box and click
“OK”“OK”
“OK”“OK”
“OK”.
Note: Note:
Note: Note:
Note: In the Adapter box, the Adapter string shows if this display is
the First View or the Second View attached to the display
controller. Please make a note of this, so that you can arrange the
displays in the correct order later.
5. Click
“OK”“OK”
“OK”“OK”
“OK” on the bottom of the Adapter Control Panel. If the
“OK”“OK”
“OK”“OK”
“OK” button on the bottom of the Adapter Control Panel is not
visible, press
“CTRL”+“Enter” “CTRL”+“Enter”
“CTRL”+“Enter” “CTRL”+“Enter”
“CTRL”+“Enter” to select
“OK”“OK”
“OK”“OK”
“OK”.
6. Click
“OK”“OK”
“OK”“OK”
“OK” in the “Windows will now apply your new desktop
settings” dialog box. Your high resolution display(s) should now
synchronize and display the Windows desktop.
7. Click
“Y“Y
“Y“Y
“Y
es” es”
es” es”
es” when asked, “Your desktop has been reconfigured.
Do you want to keep these settings?”
BarcoMed software driver installation
To Next Page
Loading...
