1 691 606 210 2015-07-29| Robert Bosch GmbH
| BSA 43xx | 39 en
Contents English
1. Symbols used 40
1.1 In the documentation 40
1.1.1 Warning notices -
Structure and meaning 40
1.1.2 Symbols in this documentation 40
1.2 On the product 40
2. User information 40
2.1 Important notes 40
2.2 Safety instructions 40
2.3 Configuration 40
2.4 Other applicable documentation 40
3. Product description 41
3.1 Intended use 41
3.2 Measurement quantities 41
3.3 Measurement visualization (operation) 41
3.3.1 General information 41
3.3.2 Check of calibration and configuration 41
3.3.3 Main window 41
3.3.4 Switching between the two halves of
the window 42
3.3.5 Selection and actuation of control ele-
ment 42
3.3.6 Main menu 42
3.3.7 Tester selection zone 42
3.4 Main switch box 43
3.5 Electrical cabinet 43
4. Operation 44
4.1 Switching the BSA 43xx on and off 44
4.2 Starting software modules 44
4.3 Software module termination 44
4.4 Operating modes 44
4.5 Brake test sequence 45
4.6 Notes on operation 45
4.6.1 General information 45
4.6.2 Notes on brake testing 45
4.6.3 Notes on brake testing for four-wheel
drive vehicles 46
4.6.4 Notes on motorcycle brake testing 46
4.6.5 Notes on suspension tester 46
4.6.6 Notes on noise simulator 46
4.6.7 Notes on side slip tester 46
4.7 Selecting test routine 46
5. Manual mode (normal operation) 48
5.1 Mode activation and deactivation 48
5.2 Test sequences 48
5.2.1 Vehicles test routine 48
5.2.2 Motorcycle test routine 50
5.2.3 Suspension tester SDL 43x 53
5.2.4 Noise simulator SDL 435 55
5.2.5 Side slip tester SDL 410 56
5.3 Remote control options 57
5.3.1 Manual entry of weights 57
5.3.2 Storing measured values 58
5.3.3 Display repetition 58
5.3.4 Deleting stored values 58
5.3.5 Displaying total deceleration 59
5.3.6 Display switching 59
5.3.7 Print-out of measurement results 59
6. Automatic mode 60
6.1 Mode activation and deactivation 60
6.2 Test sequences 60
6.2.1 Brake dynamometer BSA 43xx / BSA
44xx 60
6.2.2 Suspension tester SDL 43x 63
6.2.3 Side slip tester SDL 410 64
7. Super automatic mode 65
7.1 Mode activation and deactivation 65
7.2 Test sequence 65
7.3 Brake test options 66
7.3.1 Repetition of sub-task (Clear Last) 66
7.3.2 Parking brake on front axle 66
8. All-wheel super automatic mode 67
8.1 Mode activation and deactivation 67
8.2 Test sequence 67
9. Fault procedure 68
9.1 General information 68
9.2 Acknowledgement of warnings 68
9.3 BNet Office and SDL 43xx 69
9.4 Brake dynamometer series BSA 43xx 70
9.4.1 Warnings 70
9.4.2 Faults 70
9.5 Side slip tester SDL 410 70
9.5.1 Warnings 70
9.5.2 Faults 70
9.6 Chassis tester SDL 43x 70
9.6.1 Warnings 70
9.6.2 Faults 70
10. Appendix 71
10.1 Setting the date and time 71
10.2 Calculation methods 72
10.2.1 Deceleration 72
10.2.2 Out-of-roundness 72
10.2.3 Road surface adhesion 72
i These operating instructions describe standard test
procedures. These standard test procedures may
differ from country-specific test procedures
To Next Page
Loading...
