Brother HL-4570CDW - Page 153

3-5
Confidential
T1 solenoid ASSY Taptite bind B M3x8 1 0.35±0.05 (3.5±0.5)
Paper eject ASSY Taptite cup S M3x6 SR 5 0.70±0.10 (7±1)
Eject duct Taptite bind B M4x12 1 0.80±0.10 (8±1)
Paper eject motor Taptite bind S M3x6 2 0.70±0.10 (7±1)
AC inlet Taptite flat B M3x10 1 0.50±0.10 (5±1)
Low-voltage power supply unit Screw pan (S/P washer) M4x8 2 0.90±0.10 (9±1)
Taptite cup S M3x8 2 0.70±0.10 (7±1)
Taptite cup B M3x12 2 0.40±0.05 (4±0.5)
Taptite pan (washer) B
M4x12DA
4 0.90±0.10 (9±1)
Screw pan (S/P washer) M4x8 1 0.90±0.10 (9±1)
Low-voltage power supply PCB
ASSY
Screw cup M3x6 4 0.35±0.05 (3.5±0.5)
Registration mark sensor holder
ASSY
Taptite bind B M3x10 2 0.40±0.05 (4±0.5)
Shutter solenoid Taptite bind B M3x10 1 0.55±0.05 (5.5±0.5)
MP upper cover ASSY Taptite bind B M3x10 2 0.40±0.10 (4±1)
MP paper empty/registration
front sensor PCB ASSY
Taptite bind B M3x8 1 0.40±0.10 (4±1)
PF ASSY Taptite bind B M4x12 2 0.80±0.10 (8±1)
Shoulder screw 1 0.70±0.10 (7±1)
T1 registration front/rear sensor
PCB holder
Taptite bind B M3x10 1 0.50±0.10 (5±1)
MP sector solenoid Taptite bind B M3x8 1 0.40±0.10 (4±1)
MP drive frame Taptite bind B M3x10 3 0.50±0.10 (5±1)
High-voltage power supply
shield ASSY
Taptite cup S M3x6 SR 2 0.50±0.10 (5±1)
T2 cover rear Taptite cup S M3x10 SR 2 0.80±0.10 (8±1)
T2 cover left Taptite cup S M3x6 SR 2 0.80±0.10 (8±1)
T2 cover right Taptite cup S M3x6 SR 2 0.80±0.10 (8±1)
T2 relay PCB ASSY Taptite cup S M3x6 SR 1 0.80±0.10 (8±1)
T2 solenoid holder ASSY Taptite cup S M3x6 SR 1 0.80±0.10 (8±1)
T2 solenoid holder Screw flanged M3x3.5 1 0.50±0.10 (5±1)
T2 beam F ASSY Taptite cup S M3x6 SR 5 0.80±0.10 (8±1)
T2 beam front Taptite cup S M3x6 SR 2 0.80±0.10 (8±1)
T2 beam rear Taptite cup S M3x6 SR 4 0.80±0.10 (8±1)
T2 frame L unit Taptite bind B M4x10 1 0.80±0.10 (8±1)
Location of screw Screw type Q' ty
Tightening torque
N
·m (kgf·cm)