Case CX60C - Machine Components

To Next Page

To Previous Page

1-GENERALINFORMATION

Machinecomponents

SMIL16MEX0691FB1

Enginehood

Hydraulictank

2.Radiator9.Fueltank

Oilcooler

10.Maincontrolvalve

Engine

11.

Hydrauliccenterjoint

Mainpump

12.Bucket

Mufer

13.T ooth

Swingmotor

1-10

Main Page

Table of Contents2
General Information7
Note to the Owner7
Intended Use8
Electro-Magnetic Compatibility (EMC)8
Telematics (Optional)8
Manual Scope and Required Training Level9
Product Identification11
Operator's Manual Storage on the Machine14
Machine Orientation15
Machine Components16
Safety Information19
Signal Word Definitions19
Safety Rules - Utility Precautions20
Safety Rules21
Ecology and the Environment30
Hand Signals31
Safety Signs35
Controls and Instruments55
Access to Operator's Platform55
Door and Steps55
Operator's Seat57
Forward Controls60
Windshield66
Left-Hand Side Controls67
Safety Lock Lever69
Heating, Ventilation, or Air-Conditioning Control70
Emergency Exit Hammer74
Right-Hand Side Controls75
Engine Speed Control80
Instrument Cluster81
Remote Controller107
Dozer Blade Control Lever112
Rearward Controls113
Battery Disconnect Switch113
Storage Compartment114
Coat Hanger Hook114
Radio115
Sunshield126
Overhead Controls127
Cab Internal Lighting127
Exterior Controls128
Side Doors128
Windshield Washer Reservoir129
Cab Tilting130
Fuel Tank132
Operating Instructions133
Starting the Unit133
Anti-Theft Protection133
Starting the Engine135
Bringing the Machine up to Operating Temperature137
Operating the Machine in Hot or Cold Weather138
Operating the Machine139
Lowering the Attachment in the Event of a Failure143
Bucket Replacement144
Hydraulic Control Lever Operating Pattern145
Caution While Using Rubber Crawlers148
Stopping the Unit152
Stopping the Engine152
Moving the Unit153
Machine Travel153
Parking the Unit159
Parking the Machine159
Transport Operations161
Road Transport161
Loading the Machine Onto a Transport Trailer161
Preparing for Road Transport163
Tie Downs for Shipping163
Unloading the Machine from a Transport Trailer164
Shipping Transport165
Handling the Machine165
Recovery Transport167
Towing the Machine167
Maintenance169
General Information169
Basic Instructions169
General Specification - Diesel Fuel172
General Specification - Biodiesel Fuels173
Fluids and Lubricants175
Engine Oil Recommended Operating Temperature Range179
Releasing Pressure in the Hydraulic System180
Fuel System Bleeding185
Protecting the Electronic and Electrical Systems During Battery Charging or Welding187
Maintenance Planning188
Maintenance Chart188
Break-In Period190
Engine Oil and Filter190
Fuel Filter190
Hydraulic Oil Return Filter190
Pilot Line Filter190
Travel Reduction Gears190
Fuel Filter Water Separator190
Grease Points (Boom Swing Cylinder)190
Tightening Torques191
Grease Points (Boom and Arm)191
Every 10 Hours192
Engine Oil Level192
Engine Coolant Level193
Hydraulic Oil Level194
Fuel Filter Water Separator195
Fan and Alternator Drive Belt197
Every 50 Hours199
Grease Points (Bucket)199
Grease Points (Blade)200
Swing Ring Gear201
Track Tension202
Fuel Filter Water Separator203
Fuel Tank204
Every 250 Hours205
Grease Points (Boom and Arm)205
Swing Bearing206
Grease Points (Boom Swing Cylinder)207
Battery208
Tightening Torques212
Air Conditioner Filters213
Every 500 Hours215
Engine Oil and Filter215
Fuel Filter Water Separator216
Air Cleaner217
Fuel Filter219
Radiator and Coolers220
Radiator Fan221
Travel Reduction Gears222
Every 1000 Hours223
Hydraulic Oil Return Filter223
Oil Reservoir Breather224
Pilot Line Filter225
Travel Reduction Gears226
Every 1500 Hours227
Crankcase Breather227
Every 2000 Hours228
Hydraulic Oil Suction Filter228
Hydraulic Hoses229
Engine Coolant230
Every 5000 Hours232
Hydraulic Oil232
Every 6000 Hours234
Diesel Particulate Filter (DPF) - SF Filter234
Every 9000 Hours234
Diesel Particulate Filter (DPF) - SF and DOC Filters234
When Necessary235
Bulb Replacement235
Diesel Particulate Filter (DPF) Regeneration237
Air-Conditioning System Filters238
Control Levers238
Plastic and Resin Parts238
Fuse and Relay Locations239
Fuses239
Storage241
Preparing for Storage241
Periodic Checks242
Starting up the Machine after Storage243
Troubleshooting245
Fault Code Resolution245
Engine - Troubleshooting245
Electrical Systems - Troubleshooting246
Machine Control Unit (MCU) - Troubleshooting247
Other Systems - Troubleshooting247
Specifications249
Machine Specifications249
Dimensions252
Weights254
Accessories255
Direct Fit Buckets255
Klac Type Buckets257
Standard Buckets with Mechanical Coupler259
Standard Buckets with Hydraulic Pin Grabber Coupler261
Auxiliary Hydraulic Circuits263
Hydraulic Oil - Breaker/Auger289
Quick Coupling System - Klac Type290
Quick Coupling System - Mechanical Spring Loaded Type297
Quick Coupling System - Hydraulic Pin-Grabber Type301
Loads Handling308
Thumb Bracket311
Fuel Tank Filler Pump312
Rotating Beacon313
Fire Extinguisher314
Protection Guards315

Case CX60C - Machine Components

Table of Contents

Related product manuals