Chino DB650 User Manual

[DB600] General instruction manual
- 143 -
Screen
Item
Setting range
Default
MODE 5
Input type
□□□ □: Thermocouple B (0.0 to 1820.0°C)
□□□ □: Thermocouple R (0.0 to 1760.0°C)
□□□ □: Thermocouple S (0.0 to 1760.0°C)
□□□ □: Thermocouple N (0.0 to 1300.0°C)
□□□ : Thermocouple K1 (-200.0 to 1370.0°C)
□□□ : Thermocouple K2 (-200.0 to 500.0°C)
□□□ □: Thermocouple E (-200.0 to 900.0°C)
□□□ □: Thermocouple J (-200.0 to 1200.0°C)
□□□ □: Thermocouple T (-200.0 to 400.0°C)
□□□ □: Thermocouple U (-200.0 to 400.0°C)
□□□ □: Thermocouple L (-200.0 to 900.0°C)
: Thermocouple W-WRe5-26
(0.0 to 2310.0°C)
: Thermocouple W-WRe26
(0.0 to 2310.0°C)
: Thermocouple PlatinelII
(0.0 to 1390.0°C)
□ : Thermocouple PtRh40-20
(0.0 to 1880.0°C)
: Thermocouple Au-Pt (0.0 to 1000.0°C)
□ : ±20mV (-20.00 to 20.00mV)
: ±100mV (-100.0 to 100.0mV)
□□ □ : ±5V (-5.000 to 5.000V)
□□ : ±10V (-10.000 to 10.000V)
□ □ ： Pt 100_1 (-200.0 to 850.0°C)
□ □ ： Pt 100_2 (-200.0 to 200.0°C)
□ ： JPt 100_1 (-200.0 to 649.0°C)
□ ： JPt 100_2 (-200.0 to 200.0°C)
□ ： Pt 50 (-200.0 to 649.0°C)
□□□
Unit
: °C (Celsius) : mV
□: V
□□□
Measuring range L
Within the range (* See input type)
Measuring range H
Linear decimal point
: No decimal point
: 1 digit after decimal point
□□to
: 4 digits after decimal point
□
Linear scale zero
to
□□□
Linear scale span
to
Sensor correction
to [°C]
□□
Digital filter
to [sec]
□□□
SV limiter L
to [°C]
SV limiter H
to [°C]
Display decimal point
: No decimal point
: 1 digit after decimal point
□□to
: 4 digits after decimal point
□
MODE 6
Pulse cycle
to [sec]
□□□
Feedback zero
to [%]
□□□
Feedback span
to [%]
□
Feedback dead band
to [%]
□□□
PID dead band/
output dead band
to [%]
□□□
Control action
: Heating control
: Cooling control
Output preset
to [%]
□□
Output variation limiter L
to [%]
Output variation limiter H
to [%]
□
PV abnormal output
to [%]
□□□
Preset manual
to [%]
□□□
Operation on power ON
: READY status/program
operation RESET
: Operation right before
previous power-OFF
Control algorithm
: Position PID control
: Velocity PID control
MODE 7
Output 2 control system
□□: PID control
: Split control
□□
Output 2 P
: Two-position control
to [%]
□□□
Output 2 I
to [sec]
□□□
Output 2 D
to [sec]
□□□
Output 2 gap
to [%]
□□□
Output 2
PID dead band/
output dead band
to [%]
□□□
Output 2 control action
: Heating control
: Cooling control
Output 2 output preset
to [%]
□□□
Split Direct
to [%]
□□□
Split Reverse
to [%]
□
Output 2 pulse cycle
to [sec]
□□□
Output 2 output limiter L
to [%]
□□□
Output 2 output limiter H
to [%]
□
Output 2 variation limiter L
to [%]
Output 2 variation limiter H
to [%]
□
Output 2 preset manual
to [%]
□□□
Screen
Item
Setting range
Default
MODE a
Communication
protocol
□□：MODBUS RTU
：MODBUS ASCII
：Private
□□
Communication
function
□□: Host communication
: Digital transmission
: Digital remote input
□□
Instrument No.
to
□□□□
Communication
transmission rate
□：4800bps
□：9600bps
：19200bps
：38400bps
□
Communication
character
: 7-bit/even parity/stop bit 1
: 7-bit/even parity/stop bit 2
: 7-bit/odd parity/stop bit 1
: 7-bit/odd parity/stop bit 2
: 8-bit/no parity/stop bit 1
: 8-bit/no parity/stop bit 2
: 8-bit/even parity/stop bit 1
: 8-bit/even parity/stop bit 2
: 8-bit/odd parity/stop bit 1
: 8-bit/odd parity/stop bit 2
□□
Digital transmission
type
□: Digital SV transmission
□: Digital PV transmission
□: Digital output 1 transmission
: Digital output 2 transmission
: Digital FB transmission
□□□
Digital transmission
interval
: 100msec interval
: 200msec interval
□ : 100msec interval
□
MODE b
Transmission type
□: SV transmission signal output
□: PV transmission signal output
□: Output 1 transmission signal output
: Output 2 transmission signal output
: FB transmission signal output
□□□
Transmission scale zero
to [°C]
Transmission scale span
to [°C]
MODE c
Remote/local
switching
: Local SV operation
: Remote SV operation
Remote SV shift
to [°C]
□□
Remote filter
to [sec]
□□□
Tracking at
switch to local
: Function OFF
□: Tracking ON
□□
Remote scale zero
to [°C]
Remote scale span
to [°C]
Cascade γ
to
□□
Cascade β
to
□□□
MODE d
External input 1
□□: Function OFF
: RUN/READY switch
: AUTO/MANUAL switch
: Preset manual
: Timer 1
: Timer 2
: Alarm event reset
□: Execution No. selection 1 (Bit0)
□: Execution No. selection 2 (Bit1)
□: Execution No. selection 4 (Bit2)
□: Execution No. selection 8 (Bit3)
: Program/constant value
operation switch
□ : Program operation RUN/STOP
□ : Program operation ADVANCE
: Program operation RESET
: Program pattern 1 (Bit0)
: Program pattern 2 (Bit1)
: Program pattern 4 (Bit2)
□□
External input 2
External input 3
External input 4
External input 5
External input 6
External input 7
MODE t
Model No. (1) (2) (3) (4) (5)
See model code
Model No. (6) (7) (8) (9) (10)
Model No. (11) (12) (13) (14)
Key lock
□□: No key lock
: Operation parameter keys
locked
□□: All parameter keys locked
□□
Operation initial screen
□□: PV/SV display screen
: PV/step time display screen
□: PV/output 1 display screen
: PV/output 2 display screen
□□□
Operation screen SV
display
□□□: SV display
: Blank display
: Multi display
Bar display
□□: No display
□□: Output 1 value display
□: Output 2 value display
□□□: CT measured value display
□□□: FB measured value display
□: Step remaining/elapsed time
display
□□
Parameter storing
: Backup function OFF
□:Backup function ON
□□
Parameter initialization
□: No initialization
: Initialization executed
□□

Chino DB650 Specifications

General

Brand	Chino
Model	DB650
Category	Controller
Language	English