EasyManuals Logo

Cisco 7925G Deployment Guide

Cisco 7925G
150 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #122 background imageLoading...
Page #122 background image
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Deployment Guide
122
Default Font
Increased Font
Using the Cisco Unified Wireless IP Phone 7925G Desktop Charger
The Cisco Unified Wireless IP Phone 7925G Desktop Charger is a single phone charger including a Bluetooth speakerphone
and supports the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G running firmware version 1.4(1) or later.
When the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, or 7926G is paired to the Cisco Unified Wireless IP Phone
7925G Desktop Charger, the audio path will automatically switch to the Bluetooth speakerphone once the phone is docked.
And when removed from the desktop charger, the audio path will return to the previously used audio path (e.g. handset or
speakerphone mode).
The audio volume is controlled from the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G by pressing the
volume up or volume down button located on the left side of the phone. Mute can also be initiated by pressing the Mute button
on the left side of the phone.
The audio path is controlled from the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G by pressing and holding
the button located on the right side of the phone.
There is a battery slot in the rear of the Cisco Unified Wireless IP Phone 7925G Desktop Charger, which can be utilized for
charging a spare battery or even powering the desktop charger.
Bluetooth Pairing
The Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G can be paired to the Cisco Unified Wireless IP Phone
7925G Desktop Charger by performing the following steps.

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals