EasyManuals Logo

Cisco 7925G Deployment Guide

Cisco 7925G
150 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #84 background imageLoading...
Page #84 background image
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Deployment Guide
84
QoS Basic Service Set (QBSS)
There are three different versions of QoS Basic Service Set (QBSS) that the Cisco Unified Wireless IP Phone 7925G, 7925G-
EX, and 7926G support.
The first version from Cisco was on a 0-100 scale and was not based on clear channel assessment (CCA), so it does not account
for channel utilization, but only the 802.11 traffic traversing that individual access point’s radio. So it does not account for
other 802.11 energy or interferers using the same frequencies. The max threshold is defined on the client side, which is set to
45.
QBSS is also a part of 802.11e, which is on a 0-255 scale and is CCA based. So this gives a true representation on how busy
the channel is. The max threshold is also defined on the client side, which is set to 105.
The second version from Cisco is based on the 802.11e version, but allows the default max threshold of 105 to be optionally
configured.
Each version of QBSS can be optionally be configured on the access point.
For the Cisco Unified Wireless LAN Controller, enabling WMM will enable the 802.11e version of QBSS. There are also the
7920 Client CAC and 7920 AP CAC options, where 7920 Client CAC will enable Cisco version 1 and 7920 AP CAC enables
Cisco version 2. See the SSID / WLAN QoS Settings section for more info.
For the Cisco Autonomous Access Point, dot11 phone or dot11 phone dot11e will enable QBSS.
Dot11 phone will enable the 2 Cisco versions, where dot11 phone dot11e will enable both CCA versions (802.11e and Cisco
version 2). It is recommended to enable dot11 phone dot11e.

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals