EasyManuals Logo

Cisco 7925G Deployment Guide

Cisco 7925G
150 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #28 background imageLoading...
Page #28 background image
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Deployment Guide
28
On Call + Bluetooth
7
10
Idle
180
240
Idle + Bluetooth Enabled
165
200
If the access point does not support CCX or proxy ARP is not enabled, then the idle battery life will be up to fifty percent less.
See the Configuring Proxy ARP section for more information.
Protocols
Unscheduled Auto Power Save Delivery (U-APSD)
The Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G will utilize U-APSD (Unscheduled Auto Power Save
Delivery) for power management as long as Wi-Fi MultiMedia (WMM) is enabled in the access point configuration and the call
power save mode on the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G is set to U-APSD/PS-POLL.
U-APSD helps optimize battery life and reduces management overhead.
Below is a sample packet sequence when using U-APSD.
Power Save Poll (PS-POLL)
If WMM is disabled (disabling U-APSD support) or U-APSD support is not available on the access point, then the Cisco
Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G will utilize PS-POLL for power management when the call power
save mode on the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G is set to U-APSD/PS-POLL.
Below is a sample packet sequence when using PS-POLL.

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals