EasyManuals Logo

Cisco 7925G Deployment Guide

Cisco 7925G
150 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #130 background imageLoading...
Page #130 background image
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Deployment Guide
130
As of the 1.4(4) release, timezone support has been added; therefore the Java Timezone API is now supported.
As of the 1.4(5) release, a Java MIDlet can now be automatically launched then minimized to the background after the Cisco
Unified Wireless IP Phone 7925G, 7925G-EX, or 7926G is powered on by utilizing the Idle URL feature.
Prior to the 1.4(5) release, a Java MIDlet had to be manually launched.
To have a Java MIDlet auto-launch, the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, or 7926G must be subscribed to
the Java MIDlet application that is to be specified in the Idle URL configuration. If the Java MIDlet is not subscribed to, then
the auto-launch will fail.
Once the Java MIDlet is subscribed to, configure the Idle URL to point to the Java MIDlet application then add minimize to
the end of the URL (e.g. http://10.0.0.130/MIDlets/WifiScanner.jad -minimize)
The Java MIDlet will then automatically launch then minimize to the background once the Cisco Unified Wireless IP Phone
7925G, 7925G-EX, or 7926G registers to CUCM after being powered on.
If the Java MIDlet is closed manually after the Java MIDlet is automatically launched then minimized, then the Java MIDlet
must be manually re-launched or the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, or 7926G must be power cycled.
The Idle URL Timer parameter is not utilized for this feature as the Java MIDlet is only auto-launched immediately once the
CUCM registration event occurs after powering the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, or 7926G on.
Note: There is a space between the end of the URL and minimize, but there is not a space between and minimize.
Troubleshooting
Device Homepage
The Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G webpage provides wireless, network, and Unified CM
information.

Table of Contents

Other manuals for Cisco 7925G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7925G and is the answer not in the manual?

Cisco 7925G Specifications

General IconGeneral
Keypad number of keys12
Display diagonal2 \
Display resolution176 x 220 pixels
Call waitingYes
Lines quantity6 lines
Voice codecsG.711a, G.722, G.729a, iLBC
Security algorithms128-bit WEP, SSL/TLS, WPA
Supported network protocolsDHCP, TFTP, DNS, SCCP, SRST
Input voltage100 - 240 V
Dimensions (WxDxH)52 x 20 x 127 mm
Minimum system requirementsCisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency50/60 Hz
Storage temperature (T-T)-30 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Product typeIP Phone
Product colorGray
SafetyUL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e
Weight and Dimensions IconWeight and Dimensions
Weight138 g

Related product manuals