Cisco 7925G Deployment Guide

Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Deployment Guide
74
Call Admission Control (CAC) configuration
Voice AC - Admission control (ACM)............ Enabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Enabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video max RF bandwidth........................ 25
Video reserved roaming bandwidth.............. 6
The voice stream-size and voice max-streams values can be adjusted as necessary by using the following command.
(Cisco Controller) >config 802.11a cac voice stream-size 84000 max-streams 2
Ensure QoS is setup correctly under the WLAN / SSID configuration, which can be displayed by using the following command.
(Cisco Controller) >show wlan <WLAN id>
Quality of Service............................... Platinum (voice)
WMM.............................................. Allowed
Dot11-Phone Mode (7920).......................... ap-cac-limit
Wired Protocol................................... 802.1P (Tag=6)
When enabling Call Admission Control on the Cisco Autonomous Access Point, the admission must be unblocked on the SSID
as well.
It is required to enable Call Admission Control on the SSID configuration, regardless of Admission Control being enabled for
Voice or Video.
Load-based CAC and support for multiple streams are not present on the Cisco Autonomous Access Points therefore it is not
recommended to enable CAC on Cisco Autonomous Access Points.
The Cisco Autonomous Access Point only allows for 1 stream and the stream size is not customizable, therefore SRTP and
barge will not work if CAC is enabled.
dot11 ssid voice
vlan 21
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa cckm
admit-traffic
Also ensure that the PHY rate configured on the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G is enabled as
a nominal rate in the STREAM configuration of the Cisco Autonomous Access Point.
It is recommended to use the defaults, where 5.5, 6.0, 11.0, 12.0 and 24.0 Mbps are enabled as nominal rates for 802.11b/g and
6.0, 12.0 and 24.0 Mbps enabled for 802.11a.
If enabling the STREAM feature either directly or via selecting Optimized Voice for the radio access category in the QoS
configuration section, ensure that only voice packets are being put into the voice queue. Signaling packets (SCCP) should be
put into a separate queue. This can be ensured by setting up a QoS policy mapping the DSCP to the correct queue.

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g