ComAp InteliLite NT AMF Series - Binary Input and Output Wiring; Binary Inputs Wiring; Binary Outputs Wiring

ComAp InteliLite NT AMF Series

84 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

InteliLite

NT

– AMF20/25, SW version 1.2, ©ComAp – March 2008 26

IL-NT-AMF-Reference Guide1.2.pdf

Binary inputs

Binary outputs

+

Battery

-

iL

4k7

Ω

+

-

Power

Supply

+

Battery

-

iL

LOAD

+

-

Power

Supply

Table of Contents

Table of Contents2
General Guidelines4
- What Describes this Manual4
- Warnings4
- Text4
General Description6
- Description of the Controller System (with All Options)6
- What Is in the Package6
- IL-NT RS232 Communication Module6
- IL-NT AOUT8 Gauge Driver Module10
- IL-NT RD (SW) Remote Display Software10
- Remote Announciator IGL - RA1510
- IG IOM/PTM Module11
- IG-IB Internet Bridge13
IL-NT Terminals14
- IL-NT Terminals and Face14
Recommended Wiring15
- AMF - Wiring Diagram15
Contactors (Set Point MCB Logic = "CLOSE-OFF")16
ATS with Two Stable Positions (Set Point MCB Logic = "CLOSE-ON")16
Stand-By Applications16
ATS with Three Stable Positions (Set Point MCB Logic = "CLOSE-OFF")17
Getting Started18
- How to Install18
- Current Measurement21
- Voltage Measurement22
- Single Phase Applications22
- Analog Inputs23
- Extension Modules (CAN Bus) Connection27
- Analog Outputs28
Inputs and Outputs29
- Binary Inputs IL-NT - Default29
- Binary Inputs - List29
- Binary Outputs IL-NT - Default32
- Binary Outputs - List32
- Analog Inputs39
Setpoints41
- Password41
- Basic Settings41
- Engine Params43
- Engine Protect45
- Gener Protect47
- Automains Fail49
- Date/Time52
- Sensor Spec53
- Extension I/O54
- Act Calls/Sms54
ECU-Controlled Engine Support56
- Values Read from ECU57
- Diagnostic Messages Read from ECU57
- Analog Inputs58
- Connection Description58
Sensor Specification61
- Background of the Sensor Calibration61
- Default Sensor Curves61
Function Description62
- OFF Mode62
- MAN Mode62
- AUT Mode64
- TEST Mode64
- Circuit Breakers Timing65
Alarm Management67
- Sensor Fail (FLS)67
- Warning (WRN)67
- Shut down (SD)67
- Mains Failure (MF)67
Gen-Set Operation States70
- List of Possible Events70
- History File72
Remote Control and Data Logging73
- Direct Connection to the PC73
- PC Software - Liteedit73
- Modbus Protocol73
Remote Communication79
- Internet Connection79
- Recommended ISDN Modem79
- Recommended GSM Modem79
- Mobile SIM Card Setting79
Technical Data80
- Power Supply80
- Operating Conditions80
- Low Temperature Modification80
- Dimensions and Weight81
- Mains and Generator81
- Binary Inputs and Outputs81
- Analog Inputs81
- Speed Pick-Up Input82
- D+ Function82
- CAN Bus Interface82
- IL-NT RS232 Interface (Optional Card)83
- IL-NT AOUT8 Interface (Optional Card)83
- Igs-Ptm83
- Igl-Ra1583
- Ig-Ib84

Related product manuals

Preview: ComAp InteliLite NT AMF 25

ComAp InteliLite NT AMF 25

Preview: ComAp intelilite nt amf20

ComAp intelilite nt amf20

ComAp intelilite nt amf25

Preview: ComAp InteliLite 4 AMF 20

ComAp InteliLite 4 AMF 20

Preview: ComAp InteliLite 9

ComAp InteliLite 9

Preview: ComAp InteliLite MRS16

ComAp InteliLite MRS16

ComAp InteliLite MRS11

ComAp InteliLite MRS15

ComAp InteliLite AMF25

Preview: ComAp InteliSys NT

ComAp InteliSys NT

ComAp InteliGen NT

Preview: ComAp InteliNano NT Plus

ComAp InteliNano NT Plus