DataCard SP25 Plus - Set the IP Address, Subnet Mask, and Gateway Address

134 pages

To Next Page

To Previous Page

Page 53

Change settings

Begin when the LCD panel shows “Printer Ready” on line 1 of the display. To change settings:

1 Press the Enter key to enter the menu system.

2 Press the Up or Down Arrow key to scroll to “Configuration” on line 2.

3 Press the Enter key. You are now in the Configuration menu.

Main Page

Table of Contents3
About the Printer6
- The Outside of the Printer6
- The Inside of the Printer8
- Features and Options8
Loading Cards10
Loading Print Ribbon12
Power on the Printer14
The LCD Panel15
Making a Printer Test Card18
Data Formats for the SP Series Card Printer20
- Smartdriver Data21
- Open Card Data Format22
- Data Formats Summary24
Printer Installation26
Site Requirements27
Useful Tools28
Network Installation30
- Prepare the Printer for Installation31
- Connect the Printer to the Network32
- Set up the Network Printer35
- Set up for Your Card Design40
- SNMP Support41
Print a Card42
- From the Smartdriver42
- Using the Open Card Data Format43
Cleaning the Printer44
- Cleaning the Printer Rollers46
Getting the most out of Your Printer48
Printer LCD Settings50
- LCD Menu System51
View Status Settings52
- View the Serial Number52
- View the Firmware Revision53
- View Card Counts54
- View the Data Format55
- View the Network Address Mode, IP Addresses, and MAC Address56
Change Settings58
- Set LCD Backlighting59
- Set the Data Format60
- Set the Address Mode61
- Set the IP Address, Subnet Mask62
- Set the IP Address, Subnet Mask, and Gateway Address63
- Set the K Power65
Troubleshooting66
Printer Supplies68
- SP55 Color Print Ribbon68
- SP60 Color Print Ribbon68
- Monochrome and Topcoat Ribbon68
- Monochrome Print Ribbon69
- Cleaning Supplies69
Printer Messages70
- DM-00760 Duplex Error71
- DM-00762 Duplex Jam72
- DM-00765 no Duplex73
- DM-00767 Duplex Jam74
- IS-01206 no Card Picked75
- SY-01305 Data Error76
- SY-01306 Data Error77
SY-01310 Flash Error78
SY-01312 Flash Error79
SY-01314 Flash Error80
SY-01317 Memory Error81
SY-01325 Data Error82
SY-01327 Data Error84
SY-01331 Comm Error86
SY-01332 Hardware Error87
MS-01401, MS-01402, MS-01403 Mag Stripe Data88
MS-01404, MS-01405, MS-01406 Mag Stripe Error89
MS-01407, MS-01408, or MS-01409 Mag Stripe Error90
MS-01410, MS-01411, or MS-01412 Mag Stripe Error91
MS-01413, MS-01414, or MS-01415 Mag Stripe Error92
MS-01417, MS-01418, MS-01419, MS-01420, MS-01421 Card Jam93
MS-01424 Mag Stripe Error94
MS-01425 Mag Stripe Error95
MS-01426 EEPROM Error96
MS-01427, 1428 Mag Stripe Error97
MS-01429 Mag Stripe Data98
MS-01430 Mag Stripe Error99
MS-01431, MS-01432, MS-01433, MS-01434 EEPROM Error100
MS-01435 no Mag Stripe101
PR-01703 Printhead Error102
PR-01705, PR-01706 Card Jam104
PR-01710 EEPROM Error106
PR-01715, PR-01716 Cover Open107
PR-01718 Printhead Temp108
PR-01719 Printhead Error109
PR-01720 Ribbon Error110
PR-01721, PR-01722 EEPROM Error111
PR-01723 Hardware Error112
- PR-01724 Ribbon Break114
- PR-01726 Ribbon out116
- PR-01730 Printhead Error118
- PR-01737 Ribbon Low119
- PR-01738 Ribbon Error120
- SC-01804 no Smart Card121
Safety and Compliance (FCC)130
- Regulatory Compliance130
- Liability Statement132
- Safety132
- Acknowledgments133
Legal Notices (FCC)134
- Liability Statement134
- Regulatory Compliance134
- Trademark Acknowledgments134
- Proprietary Notice134

DataCard SP25 Plus - Set the IP Address, Subnet Mask, and Gateway Address

Table of Contents

Other manuals for DataCard SP25 Plus

Related product manuals