EasyManuals Logo

Denon AVR-3808CI Service Manual

Denon AVR-3808CI
215 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #12 background imageLoading...
Page #12 background image
12
AVR-3808CI / AVR-3808 / AVC-3808
CAUTION IN SERVICING
Before the Digital P.W.B. are replacedh
If you cannot specify the cause of the Digital P.W.B. defect,
carry out "Initializing" "Update to latest firmware".
The defect may be cleared.
See the following for the method of initializing the μcom.
When replacing the Digital P.W.B. and CPU
P.W.B. h
When replacing the digital P.W.B. and CPU P.W.B., be sure
to perform "Initialize" "Update to latest firmware" after re-
placement.
See the following for the method of initializing the μcom.
When performing a firmware update, it may take about 2 
minutes to start up, depending on the firmware combination.
After completing the update, check that the latest version is
displayed by operating the version display function.
Initializing AV SURROUND RECEIVER/AM-
PLIFIER
AV SURROUND RECEIVER/AMPLIFIER initialization should
be performed when the µcom, peripheral parts of µcom, and
Digital P.W.B. are replaced.
1. Switch off the unit.
2. Hold the following Cursor button and , and switch on
the unit.
3. Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 but-
tons and the microprocessor will be initialized.
Note:If step 3 does not work, start over from step 1.
All user settings will be lost and this factory
setting will be recovered when this initializa-
tion mode.
So make sure to memorize your setting for re-
storing after the initialization.
JIG to use for servicing
When you repair the printing board, you can use the following
JIG. Please order to Denon Official Service Distributor in your
region if necessary.
Extention cable kit h
00D SPK- 561 EXTENSION UNIT KIT : 1 Set
00D SPK- 562 TUCP CONN. JOINT KIT : 1 Set
Extention cable for Idling Current g
Parts Number for Extension Cables and Quantity of Unit
How to use and Adjust Idle Current
1. The thin and hard plate (ex. Ruler) is fixed with the tape
behind the cable.
2. The voltmeter is connected with the other side of the ex-
tension cable.
3. Refer to ADJUSTMENT(Idling Current).
Parts Number Parts Name Q'ty / unit Remarks
612050082004D 6P 250mm NH 1 L=250mm 6P NH Cable
612050083007D 8P 250mm NH 1 L=250mm 8P NH Cable
h
2,3
1,2
サービス時の注意事項
Digital 基板の交換の前に h
Digital基板の不具合の原因が特定出来ない場合は、"初化"→
" 最新ファームウェアにアップデー " をおこなってください。
不具合が解消される場合があります。
・マイコンの初期化方法については、下記をご覧ください。
Digital 基板、CPU 基板を交換した場合h
Digital 基板、CPU 板を交換した場合は、交換後に必ず、"
期化 " " 最新ファームウェアにアップデート " をおこなってく
ださい。
マイコンの初期化方法については、下記をご覧ください。
ファームウェアのアップデートを行う際に、ファームウェ
の組合せにより、起動するまでに2分程度かかる場合が
あります。
アップデート完了後、バージョン表示機能を操作して、 最新
バージョンが表示されることを確認してください。
AVサラウンドレシーバー / アンプの初期化
について
マイコンやマイコン周辺部品、Digital 基板等を交換した場
合は、AV サラウンドレシーバー / アンプの初期化を行って
下さい。
1. ON/OFF ボタンを OFF にします。
2. Cursorボタン△と▽を同時に押しながら、ON/OFF ボタ
ンを押して ON にします。
3. ディスプレイ表示が約 1秒間隔で点滅するのを確認後、
2つのボタンから指を離します。
マイコンが初期化されます。
注意 :・上記 3 の状態にならない場合は、もう一度操作 1
からやり直してください。
初期化を行うとお客様が設定した内容が工場出
荷状態に戻りますので、あらかじめ設定内容を
控えておき初期化後再設定してください。
サービス時に使用する治具について
基板を修理する際、使用する治具は 下記のとおりです。
必要に応じて販社サービスへ注文下さい。
延長ケーブルキットh
00DSPK-561EXTENSIONUNITKIT:1
00DSPK-562TUCPCONN.JOINTKIT:1
アイドル電流用延長ケーブルg
延長ケーブルの品番と使用本数
使用方法と調整方法
1. ケーブルに沿わして定規などの硬い板をテープで止めて
ください。
2. ケーブルのコネクタとは反対側に電圧計を接続します。
3. 調整の項目を参照してアイドル電流を調整します。
Parts Number Parts Name Q'ty / unit Remarks
612050082004D 6P 250mm NH 1 L=250mm 6P NH Cable
612050083007D 8P 250mm NH 1 L=250mm 8P NH Cable
h

Table of Contents

Other manuals for Denon AVR-3808CI

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-3808CI and is the answer not in the manual?

Denon AVR-3808CI Specifications

General IconGeneral
BrandDenon
ModelAVR-3808CI
CategoryReceiver
LanguageEnglish

Related product manuals