Parts Data
81
WCVD18HCS-10 120 volts 60hz. Single Phase
WCVD18HCS-12 208-240 volts 60hz. Single Phase or Three Phase
WCVD25HCS-12 208-240 volts 60hz Single Phase or Three Phase
WCVD40HCS-12 208-240 volts 60hz Single Phase or Three Phase
WCVD55HCS-12 208-240-volts 60hz Single Phase or Three Phase
WCVD75HCS-12 208-240 volts 60 hz Single Phase or Three Phase
Key Description T-300 T-400 T-600 T-900 T-1200 QTY
-- Kit, Door Gasket Expander (large) 9732-139-002 9732-139-002 9732-139-002 9732-139-002
-- Kit, Door Gasket Expander (small) 9732-139-001 9732-139-001 9732-139-001 9732-139-001
-- Hose, W
ater Supply 3/8” I.D. x 48” 9990-027-011 9990-027-011 9990-027-011 2
-- Hose, Water Supply 5/8” I.D. x 48” 9990-027-013 9990-027-013 2
-- Washer, Inlet Hose (furnished) 8641-242-000 8641-242-000 8641-242-000 8641-242-000 8641-242-000 2
-- Strainer, Inlet Hose (furnished) 9565-003-001 9565-003-001 9565-003-001 9565-003-001 9565-003-001 2
-- Drain hose 10 ft. length x 2-1/4” I.D 9242-417-002
-- Drain hose 10 ft. length x 3” I.D. 9242-417-003 9242-417-003 9242-417-003 9242-417-003
-- Bevel Washer for 5/8” bolt used in 8641-586-002 8641-586-002 8641-586-002 8641-586-002 8641-586-002
installations using angle iron bases
-- Bevel Washer for 3/4” bolt used in 8641-586-003 8641-586-003 8641-586-003 8641-586-003 8641-586-003
installations using angle iron bases
-- Sealing compound 8538-151-001 8538-151-001 8538-151-001 8538-151-001 8538-151-001
-- TORX#20 8545-051-002 8545-051-002 8545-051-002 8545-051-002 8545-051-002
-- Flow Restrictors (in dispenser ) 9475-002-002 9475-002-002 9475-002-002 9475-002-002 9475-002-003 2
-- Battery (used on Control PCB) 8612-001-001 8612-001-001 8612-001-001 8612-001-001 8612-001-001
-- Special Tool for adjusting spacing 8545-056-001 8545-056-001
between outer tub front and
cylinder front
-- VFD Filter options (1 phase) 120v 9183-041-001
-- VFD Filter options (3 phase) 9183-042-001 9183-037-001 9183-037-001 9183-037-001 9183-037-001
-- VFD Filter options (1 phase) 9183-044-001 9183-045-001 9183-045-001 9183-045-001 9183-045-001
-- Puller for pushing cylinder out
of bearings must be
purchased from local sources.
-- Clamps to hold tub front to outer tub Vise Grip #11R Vise Grip #11R
when installing tub front
-- OPL OS2 platform for 9504-011-001 9504-011-001 9504-011-001 9504-011-001 9504-011-001
infared programming devices
-- OPLBearing & Seal Kit 9732-219-001 9732-219-003 9732-219-005 9732-219-007 9732-219-007
V-Series Accessories
----
Cylinder Weld Assembly with Seals
9732-119-001
9732-120-001
To Next Page
Loading...
Need help?
General
