Eaton PowerXL DH1 Series - Table 80. Analog Output 1 - P3.3

69POWERXL DH1 SERIES ADJUSTABLE FREQUENCY DRIVES MN040041EN—August 2019 www.eaton.com
Chapter 6 — PID Application
Code Parameter Min. Max. Unit Default ID Note
P3.2.33

PID1 Superv Enable 0 1346 0 = Disabled
1 = Enabled
P3.2.34

PID1 Superv Upper Limit See Par ID 1298 See Par ID 1300 Varies 0.00 1347
P3.2.35

PID1 Superv Lower Limit See Par ID 1298 See Par ID 1300 Varies 0.00 1349
P3.2.36

PID1 Superv Delay 0 3000 s 0 1351
P3.2.37

PID2 Superv Enable 0 1408 See Par ID 1346
P3.2.38

PID2 Superv Upper Limit See Par ID 1360 See Par ID 1362 Varies 0.00 1409
P3.2.39

PID2 Superv Lower Limit See Par ID 1360 See Par ID 1362 Varies 0.00 1411
P3.2.40

PID2 Superv Delay 0 3000 s 0 1413
Table 80. Analog Output 1 — P3.3
Code Parameter Min. Max. Unit Default ID Note
P3.3.1

AO1 Mode 0 227 See Par ID 222
P3.3.2

AO1 Function 1 146 0 = Not Used
1 = Output Frequency
2 = Freq Reference
3 = Motor Speed (0-Nom)
4 = Motor Current (0-Nom)
5 = Motor Torque (0-Nom)
6 = Motor Power (0-Nom)
7 = Motor Voltage (0-Nom)
8 = DC-Bus Voltage
9 = PID1 Setpoint
10 = PID1 Feedback 1
11 = PID1 Feedback 2
12 = PID1 Control Error Value
13 = PID1 Control Output
14 = PID2 Setpoint
15 = PID2 Feedback 1
16 = PID2 Feedback 2
17 = PID2 Control Error Value
18 = PID2 Control Output
19 = AI1
20 = AI2
21 = Output Freq (-2-+2N)
22 = Motor Torque (-2-+2N)
23 = Motor Power (-2-+2N)
24 = PT100 Temperature
25 = FB Process Data Input 1
26 = FB Process Data Input 2
27 = FB Process Data Input 3
28 = FB Process Data Input 4
29 = FB Process Data Input 5
30 = FB Process Data Input 6
31 = FB Process Data Input 7
32 = FB Process Data Input 8
33 = SlotA PT100 Temp Channel 1
34 = SlotA PT100 Temp Channel 2
35 = SlotA PT100 Temp Channel 3
36 = SlotB PT100 Temp Channel 1
37 = SlotB PT100 Temp Channel 2
38 = SlotB PT100 Temp Channel 3
39 = User Defined Output
40 = Motor Current (-2-+2N)
P3.3.3

AO1 Minimum 1 149 0 = 0V / 0 mA
1 = 2V / 4 mA
P3.3.4

AO1 Filter Time 0.00 10.00 s 1.00 147
P3.3.5

AO1 Scale 10 1000 % 100 150
P3.3.6

AO1 Inversion 0 148 See Par ID 181
P3.3.7

AO1 Offset -100.00 100.00 % 0.00 173
ote:N

Parameter value can only be changed after the drive has stopped.

Parameter value will be set to be default when changing macros.

Input function is Level sensed.
Table 79. Supervisions — P3.2, continued