Eaton XV300 - Page 73

To Next Page

To Previous Page

5. External connections

5.8 XV300 multi touch display as SmartWire-DT coordinator

Config-LED



Red continuous light

The project configuration and the stored tar-

get configuration are not compatible with

each other.



GREEN flashing

The project configuration is compatible with

the stored target configuration.



Green continuous light

The project configuration matches the stored

target configuration

XV30004/19 MN048017ENwww.eaton.eu

Main Page

XV300 Manual1
Imprint2
Before Commencing the Installation3
Table of Contents5
Table of Content5
Figure 24: Mounting6
About this Documentation9
List of Revisions9
Target Group10
Legal Disclaimer11
Device Designations and Abbreviations11
Writing Conventions11
Table 1: Format Conventions Used Throughout this Manual11
Hazard Warnings12
Documents with Additional Information13
Description14
Function14
Features14
Options14
Notes15
Smartwire-DT15
Xn30015
Use as Intended16
Device Models - Versions and Part Nos17
Basic Features17
Device Variants17
Optional Features17
Figure 1: Front with Plastic Frame18
Figure 2: Service Side with Optional Interfaces18
Figure 3: Front with Plastic Frame18
Figure 5: Front Side with Aluminum Frame18
Table 2: Enclosure Versions for Front Mounting18
Figure 7: Front Side with Aluminum Mounting19
Figure 8: Service Side with Optional Interfaces19
Figure 9: Front Side with Aluminum Mounting19
Figure 10: Service Side with Optional Interfaces19
Table 3: Enclosure Versions for Rear (Panel)19
Operating and Indication Elements20
Overview20
Figure 4: Service Side with Optional Interfaces20
Figure 6: Service Side with Optional Interfaces20
Interfaces to Peripheral Devices21
Figure 11: Interfaces21
How to Interpret the Part Number22
Table 6: Display Size22
Table 7: Interfaces22
Table 8: Version22
Table 9: Bundles with Visualization Software22
Accessory Devices23
Indication Label24
Support24
Figure 12: Example for a Nameplate24
Conditions for Underwriters Laboratories Inc. (UL) Listing25
Marine Approvals26
Safety Regulations27
Basics27
Mandatory Requirements, Personnel Requirements27
Occupational Safety27
Personnel Qualifications27
Device Documentation27
Installation, Maintenance, and Disposal28
Prerequisites for Proper Operation28
Device-Specific Hazards30
Installation35
Prerequisites for the Area of Application35
Installation Position35
Temperatures35
Figure 13: Space Required to Remove the SD35
Aeration and De-Aeration36
Criteria for the Installation Position37
Figure 14: Cooling Air Circulation37
Figure 15: Mounting Distance37
Figure 16: Mounting Position38
Technical Conditions for Acceptance by Underwriters Laboratories Inc. (UL)39
Conditions for Marine Approvals40
Radio Interference Suppression Filter for the 24 V DC Supply40
Figure 17: Engineering Example for Integration of Radio Interference Suppression Filters40
Unpacking and Checking the Equipment Supplied41
Table 10: Std. Pack41
Mounting42
Fixing and Sealing42
Front Mounting42
Figure 18: Peripheral Gasket Along the Entire43
Figure 19: Pre-Installing the Holding Brack- Etsscrew the Set Screwsinternal Hexagon44
Figure 20: Installing the Holding Brackets44
Rear (Panel) Mounting Rear (Panel) Mounting46
Figure 21: M4 X 12 Weld Studs on Sheet46
Figure 22: Dimensional Drawing for Mounting46
Figure 23: Dimensional Drawing for Mountingxv-313-1047
Preparing the Device for Operation48
Functional Earthing XV30051
Figure 25: Screwing the Functional Earth con51
Table 11: Specification Functional Earthing51
Power Supply - Electrical Connection52
Figure 26: Connecting the Screw Terminals on52
Table 12: Configuration Plug Connector MSTB52
Table 13: Specifications for Connection to52
Commissioning54
Initial Commissioning54
Running the XV30054
External Connections56
Layout of Interfaces57
Optional Interfaces57
Figure 28: Interfaces Included on All HMI Panels57
SD Card58
USB Interfaces59
USB Host59
USB Device59
Ethernet 1, Ethernet60
Serial Interfaces for Communication with Plcs or Devices61
Com161
Wiring61
Table 14: Pin Assignment COM1 RS-232, Not Gal61
Table 15: RS-232 Cable Length Based on Baud61
Com262
Wiring62
Table 16: Pin Assignment COM2 RS-485, Not Gal62
Table 17: Specifications for RS-485 Wiring62
Topology63
Figure 33: Bus Segment with Four Nodes63
CAN1 Interface for Protocols Canopen and J193964
Wiring64
Table 18: PIN Assignment for CAN Interface as64
Table 19: Specifications for CAN Wiring64
CAN-Bus-Topology65
Figure 34: CAN Bus Segment with Four Nodes65
PROFIBUS Interface66
Wiring66
Table 20: Pin Assignment for Profibus DP, Not66
Table 21: Specifications for Profibus Wiring66
Profibus Topology67
XV300 Multi Touch Display as Smartwire-DT Coordinator68
Smartwire-DT Powered Via POW/AUX68
Figure 36: Smartwire-DT Power Connector68
SWD Power Supply Voltages69
Smartwire-DT Interface70
Table 23: Wiring the Plug Connector70
Table 24: Overcurrent and Short-Circuit Protective Device Standards70
Table 25: Pin Assignment for Smartwire-DT Ribbon Cable Interface (Pin Header, 8-Pin)70
Commissioning the Smartwire-DT Network71
Table 26: SWD-LED72
Table 27: Config-LED72
Faults74
Maintenance75
Cleaning and Maintenance75
Capacitive Multi-Touch Technology (PCT)75
Battery75
Repairs75
Storage, Transport and Disposal76
Storage and Transport76
Disposal77
Table 28: Materials Used XV30078
Appendix79
Technical Data80
Data Sheets80
Specifications: Dimensions and Weight80
Mounting Surrounds for Rear (Panel) Mounting87
Figure 46: Installation Panel for XV-313-7087
Figure 47: Installation Panel for XV-313-1087
General Data88
Specifications: Interfaces90
Front Mounting90
Front Mounting with Smartwire-DT Connection93
Rear (Panel) Mounting96
Figure 30: USB 2.0, Not Galvanically Isolated96
Figure 31: USB 2.0, Not Galvanically Isolated96
Table 5: Type96
Rear (Panel) Mounting with Smartwire-DT Connection98
Information on the Power Supply100
Approvals and Declarations102
Table 39: Overcurrent and Short-Circuit Protective Device Standards103
Further Reading104
Alphabetical Index107
List of Figures111
List of Tables112
Glossary113

Eaton XV300 - Page 73

Table of Contents

Related product manuals