Emerson Daniel Danalyzer 1000 - Preparation; Installing the Analyzer; Installing the GC Controller

MODEL 1000 SEP 2005
TABLE OF CONTENTS
v
3.2 PREPARATION .................................................. 3-14
3 . 2 .1 In t ro d u c tio n ....................................................... 3-14
3.2.2 Site Selection...................................................... 3-14
3.2.3 Unpacking the Unit ................................................. 3-15
3.2.4 Necessary Tools and Components .....................................3-16
3.2.5 Optional Tools and Components.......................................3-18
3.3 INSTALLING THE ANALYZER .................................... 3-20
3.3.1 Point-to-Point Wiring Guide, Analyzer-Controller . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
3.3.2 Analyzer AC-Power Wiring ..........................................3-27
3.3.3 Sample and Gas Lines ...............................................3-29
3.4 INSTALLING THE GC CONTROLLER .............................3-32
3.4.1 Modbus Slave Address (COM ID) Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
3.4.2 Controller-Analyzer Wiring ..........................................3-36
3.4.3 Controller-PC Wiring (Serial Connections) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
3.4.3.1 Before Connecting ...............................................3- 38
3.4.3.2 PC-to-GC, Front Panel Quick and Easy RS-232 . . . . . . . . . . . . . . . . . . . . . . . . 3-41
3.4.3.3 PC-to-GC, Permanent Cable Connection for Short Distance RS-232 . . . . . . . . 3-42
3.4.3.4 PC-to-GC, Long Distance with RS-422 or RS-485 . . . . . . . . . . . . . . . . . . . . . . 3-44
3.4.4 CPU and COM4A Serial Communications Setups . . . . . . . . . . . . . . . . . . . . . . . . . 3-46
3.4.4.1 CPU RS-232/RS-422/RS-485 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50
3.4.4.2 CPU RS-232 Configuration ........................................3- 51
3.4.4.3 CPU RS-422 Configuration ........................................3- 53
3.4.4.4 CPU RS-485 Configuration ........................................3- 57
3.4.4.5 CPU COM1/COM2, Keyboard and Printer Output Header . . . . . . . . . . . . . . . . 3-59
3.4.4.6 CPU COM3/COM4 Output Header ..................................3-59
3.4.4.7 COM4A RS-232/RS-422/RS-485 Configuration . . . . . . . . . . . . . . . . . . . . . . . . 3-60
3.4.4.8 COM4A RS-232 Configuration .....................................3-65
3.4.4.9 COM4A RS-422 Configuration .....................................3-69
3.4.4.10 COM4A RS-485 Configuration .....................................3-71
3.4.4.11 Parallel Printer Interface ...........................................3-73
3.4.4.12 P/C104 Bus Interface .............................................3- 74
3.4.4.13 Silicon Disk Configuration .........................................3-75
3.4.4.14 Multi-I/O Connector ..............................................3- 77
3.4.4.15 Parallel I/O Configuration .........................................3-78
3.4.5 Controller-Printer Wiring ............................................3-81
3.4.6 Discrete (Digital) I/O Wiring .........................................3-83
3.4.7 Analog I/O Wiring ................................................. 3-86