Emerson Rosemount 5300 Series - Page 243

Emerson Rosemount 5300 Series

488 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Emerson Instrument and Valve Response Center representatives will explain the additional

information and procedures necessary to return goods exposed to hazardous substances.

Reference Manual Service and troubleshooting

00809-0100-4530 April 2019

Reference Manual 243

Table of Contents

Default Chapter5
- Table of Contents5
Chapter 1 Introduction9
- Using this Manual9
- Product Recycling/Disposal10
Chapter 2 Transmitter Overview11
- Theory of Operation11
- Application Examples12
- Components of the Transmitter14
- System Integration16
- Probe Selection Guide19
- Measuring Range21
- Process Characteristics23
- Vessel Characteristics25
Chapter 3 Mechanical Installation27
- Safety Messages27
- Mounting Considerations28
- Shorten the Probe44
- Centering Disc for Pipe Installations60
- Mount Device on Tank67
- Anchor the Probe88
Chapter 4 Electrical Installation93
- Safety Messages93
- Cable/Conduit Entries94
- Grounding94
- Cable Selection95
- Hazardous Areas96
- 4-20 Ma/Hart96
- Hart99
- To Modbus ® Converter (HMC)99
- FOUNDATION ™ Fieldbus105
- Connect Wiring and Power up107
- Optional Devices110
Chapter 5 Configuration113
- Safety Messages113
- Overview113
- Host System Integration115
- Establish HART ® Communication for Transmitter with HART to Modbus ® Converter119
- Basic Configuration Using Rosemount Radar Master122
- Basic Configuration Using AMS Device Manager and Handheld Communicator139
- Basic Configuration Using Deltav140
- Foundation140
- OUNDATION Fieldbus Overview144
- Modbus ® Communication Protocol Configuration147
- Configure the Alarm Output for the Modbus ® Transmitter153
- HART ® Multi-Drop Configuration156
Chapter 6 Operation159
- Safety Messages159
- Using the Display Panel160
- Specify Display Panel Variables161
- View Measurement Data165
Chapter 7 Service and Troubleshooting169
- Safety Messages169
- Diagnostic Messages171
- LCD Error Messages177
- LED Error Messages178
- FOUNDATION ™ Fieldbus Error Messages180
- Troubleshooting Guide183
- Diagnostics189
- Level and Distance Calibration192
- Service and Troubleshooting Tools194
- Application Challenges224
- Upgrade the HART ® to Modbus ® Converter Firmware Using Rosemount Radar Master234
- Replace the Transmitter Head237
- Changing a Probe238
- Service Support242
- Safety Instrumented Systems (4-20 Ma Only)245
  - Safety Messages245
Chapter 8 Safety Instrumented Systems (4-20 Ma Only)245
- Terms and Definitions246
- Safety Instrumented System (SIS) Certification246
- Safety-Certified Identification247
- Installation in SIS Applications248
- Configuring in SIS Applications249
- Perform Proof Test for SIS Applications251
- Inspection267
- Specifications268
Appendix A Specifications and Reference Data271
- Performance Specifications271
- Functional Specifications280
- Physical Specifications300
- Dimensional Drawings307
- April308
- Proprietary Flanges324
- Flushing Connection Rings325
- Ordering Information326
- Spare Parts and Accessories343
Appendix B Product Certifications359
- European Directive Information359
- Safety Instrumented Systems (SIS)359
- Ordinary Location Certification359
- Installing Equipment in North America359
- Usa359
- Canada361
- Europe362
- International364
- Brazil367
- China368
- Technical Regulations Customs Union (EAC)369
- Japan370
- Republic of Korea370
- India371
- Ukraine371
- Uzbekistan371
- Combinations372
- Additional Certifications372
- Pattern Approval374
- Conduit Plugs and Adapters374
- Installation Drawings376
Appendix C Configuration Parameters381
- Menu Tree381
- Basic Configuration Parameters385
Appendix D Advanced Configuration397
- Safety Messages397
- User Defined Upper Reference Point397
- Probe End Projection398
- Adjust the Echo Tracking Settings402
- Dielectric Constant Settings403
- Dynamic Vapor Compensation405
- Signal Quality Metrics414
- Switch Alarm Limits (HART ® Only)417
- Detecting Thin Interface Layers418
Appendix E Remote Mounting421
- Remote Housing, New Units421
- Remote Connection, Field Retrofit421
- Install Remote Housing422
- Remote Housing Configuration in Rosemount Radar Master424
Appendix F Level Transducer Block425
- Overview425
- Parameters and Descriptions426
- Supported Units433
- Diagnostics Device Errors435
Appendix G Register Transducer Block437
- Overview437
- Register Access Transducer Block Parameters437
Appendix H Advanced Configuration Transducer Block441
- Overview441
- Advanced Configuration Transducer Block Parameters441
Appendix I Resource Transducer Block445
- Overview445
- Parameters and Descriptions445
- Alerts450
- Alarm Priority452
- Process Alarms453
- Recommended Actions for Alerts453
Appendix J Analog-Input Block457
- Analog Input Block457
- Simulation461
- Damping461
- Signal Conversion462
- Block Errors463
- Modes464
- Alarm Detection464
- Advanced Features465
- Configure the AI Block466
Appendix K Rosemount 5300 with HART to Modbus Converter473
- Safety Messages473
- Introduction474
- Workflow for Commissioning a Transmitter with Modbus Protocol475
- Common Modbus ® Host Configuration476
- Specific Modbus ® Host Configuration480

Other manuals for Emerson Rosemount 5300 Series

Quick Start Guide56 pages

Product Data Sheet52 pages

Related product manuals

Emerson Rosemount 5302

Emerson Rosemount 5301

Preview: Emerson Rosemount 56

Emerson Rosemount 56

Preview: Emerson Rosemount 520

Emerson Rosemount 520

Preview: Emerson Rosemount 5408

Emerson Rosemount 5408

Preview: Emerson Rosemount 5402

Emerson Rosemount 5402

Preview: Emerson ROSEMOUNT 5081-A

Emerson ROSEMOUNT 5081-A

Preview: Emerson Rosemount 5081-T

Emerson Rosemount 5081-T

Preview: Emerson Rosemount 5400 Series

Emerson Rosemount 5400 Series

Preview: Rosemount Analytical HART 5081-A-HT

Rosemount Analytical HART 5081-A-HT

Preview: Emerson Rosemount 702

Emerson Rosemount 702

Preview: Emerson Rosemount 1056

Emerson Rosemount 1056