Enerpac JS125 - Page 148

www.enerpac.com
Document number: ED.03783.00.001.ENG rev 4 Page 148 of 153
suitable, select an appropriate combination of mask and filter. Select a filter suitable for combined
particulate/organic gases and vapours [Type A/Type P boiling point > 65°C (149°F)] meeting EN14387
and EN143.
Thermal
hazards
Not applicable
8.4.
Environmental exposure controls
General
advice
Take appropriate measures to fulfill the requirements of relevant environmental protection legislation.
Avoid contamination of the environment by following advice given in Section 6. If necessary, prevent
undissolved material from being discharged to wastewater. Wastewater should be treated in a municipal
or industrial wastewater treatment plant before discharge to surface water. Local guidelines on emission
limits for volatile substances must be observed for the discharge of exhaust air containing vapour.
9. Physical and chemical properties
9.1.
Information on basic physical and chemical properties
Appearance
Liquid
Colour
Colourless
Odour
Slight hydrocarbon
Odour Threshold
Data not available
pH
Not applicable
pour point
: -48 °CMethod: ISO 3016
Initial boiling point and boiling range
> 280 °Cestimated value(s)
Flash point
260 °C, Method: ASTM D92 (COC)
Evaporation rate
Data not available
Flammability (solid, gas)
Data not available
Upper explosion limit
Typical 10 %(V)
Lower explosion limit
Typical 1 %(V)
Vapour pressure
< 0,5 Pa (20 °C)
estimated value(s)
Relative vapour density
> 1estimated value(s)
Relative density
0,832 (15,0 °C)
Density
: 832 kg/m3 (15,0 °C) Method: ISO 12185
Solubility(ies)
Water solubility
negligible
Solubility in other solvents
Data not available
Partition coefficient: n- octanol/water
log Pow: > 6(based on information on similar products)
Auto-ignition temperature
> 320 °C
Decomposition temperature
Data not available
Viscosity
Viscosity, dynamic
Data not available
Viscosity, kinematic
46 mm2/s (40,0 °C), Method: ISO 3104
8,7 mm2/s (100 °C), Method: ISO 3104
Explosive properties
Not classified
Oxidizing properties
Data not available
9.2.
Other information
Conductivity
This material is not expected to be a static accumulator
10. Stability and reactivity
10.1.
Reactivity
The product does not pose any further reactivity hazards in addition to those
listed in the following sub-paragraph
10.2.
Chemical stability
Stable. No hazardous reaction is expected when handled and stored according
to provisions
10.3.
Possibility of hazardous reactions
Hazardous reactions
Reacts with strong oxidising agents.
10.4.
Conditions to avoid
Conditions to avoid
Extremes of temperature and direct sunlight
10.5.
Incompatible materials
Materials to avoid
Strong oxidising agents
10.6.
Hazardous decomposition products
Hazardous decomposition products
No decomposition if stored and applied as directed
11. Toxicological information
11.1.
Information on toxicological effects
Basis for assessment
Information given is based on data on the components and the toxicology of similar
products. Unless indicated otherwise, the data presented is representative of the
product as a whole, rather than for individual component(s).
Information on likely routes of
exposure
Skin and eye contact are the primary routes of exposure although exposure may occur
following accidental ingestion
Acute oral toxicity
Product
LD50 rat: > 5.000 mg/kg
Remarks: Low toxicity: Based on available data, the classification criteria are not met.
Acute inhalation toxicity
Remarks: Based on available data, the classification criteria are not met.
Acute dermal toxicity
LD50 Rabbit: > 5.000 mg/kg
Remarks: Low toxicity: Based on available data, the classification criteria are not met.
Skin corrosion/irritation
Product
Remarks: Slightly irritating to skin., Prolonged or repeated skin contact without proper
cleaning can clog the pores of the skin resulting in disorders such as oil
acne/folliculitis., Based on available data, the classification criteria are not met.
Serious eye damage/eye irritation