How to improve cut quality of Exakt Saw?
If the cut quality of your Exakt Saw is declining, consider these potential causes and solutions: * The cutting band might be soiled; clean it. * The cutting band could be worn; replace it. * The yellow belt may be dirty; clean it. * A faulty yellow belt could also be the problem; replace it. * The cutting band speed might be incorrect; adjust it accordingly.
What to do if there is no cooling water in my Exakt 312 Saw?
If there is no cooling or flush water in your Exakt Saw, here are a few things you can check: * Make sure the water supply is turned on. * Check for any blockages in the water supply and clean if necessary. * Ensure the cooling water control is open. * Verify the flush water control is open.
Why doesn't waste water drain away from my Exakt 312 Saw?
If waste water isn't draining away from your Exakt Saw, it could be due to: * A blocked drain. Clean the drain nozzle and check/clean the work table tray. * The drain being higher than the drain nozzle. Ensure there is an adequate gradient.
Why my Exakt Saw 312 won't start?
Your Exakt Saw 312 might not be starting due to several reasons. Here's what to check: * Ensure the main switch is turned ON. * Press the acknowledge button. * Make sure the doors are completely closed, and then press the acknowledge button. * Verify the emergency-stop pushbutton is not pressed; pull it out to unlock, then press the acknowledge button. * If the electronic speed control has a fault (like overload), press the stop button for about 3 seconds and restart the motor. * Check the fuse and replace if needed. * Inspect the mains cable for faults; a service engineer should replace it if necessary. * Confirm the mains plug is properly plugged in, the main switch is ON, and the acknowledge button is pressed. * Check if there is power at the socket. * Examine the b...
Comprehensive safety guidelines for operation, maintenance, and handling.
Details on the EXAKT 312's safety mechanisms like emergency stop and nip guards.
Explanation of visual symbols indicating potential risks and hazards.
Defines the severity levels of hazards associated with signal words.
Explanation of symbols used for notes, tools, and list formats in the manual.
Defines the intended use, target users, and limitations of the EXAKT 312.
Highlights advantages over conventional saws and lists standard equipment.
Lists all components included in the standard package of the EXAKT 312.
Details of accessories available to enhance the EXAKT 312's functionality.
Illustrated views of the EXAKT 312 from different angles with component labels.
Guidance on safely transporting and selecting a suitable location for the EXAKT 312.
Step-by-step instructions for setting up, levelling, and assembling the unit.
Procedure for connecting the EXAKT 312 to water, drainage, and power systems.
Steps for performing and concluding an initial test run of the EXAKT 312.
Visual inspection procedure to ensure the cutting band is correctly centred.
Essential steps and safety checks before commencing regular cutting tasks.
Detailed instructions for adjusting guides, speed, and cutting samples.
Procedure for safely shutting down the EXAKT 312 after completing cutting tasks.
Guidelines for general cleaning, hygiene regulations, and cleaning schedules.
Information on suitable cleaning agents and steps for cleaning/pre-disinfecting.
Instructions for disinfecting the cutting band, pulleys, and guides.
Procedure for reassembling parts after cleaning and disinfection.
Tasks for maintaining the cutting band and removing it.
Maintenance tasks to be performed at weekly, six-monthly, and annual intervals.
Procedures for replacing fuses and checking functions.
Common faults, their causes, and recommended rectification steps.
Guidelines for the proper disposal of the EXAKT 312 packaging materials.
Information on environmentally sound disposal methods for the EXAKT 312 unit.
Detailed specifications including dimensions, weight, voltage, and power.
List of available spare parts for the EXAKT 312 with item numbers.
List of consumable items such as cutting bands and belts.
List of optional accessories for enhancing EXAKT 312 functionality.
Definitions of technical terms used within the EXAKT 312 manual.
Alphabetical listing of topics and their corresponding page numbers.
Official confirmation of the EXAKT 312's compliance with EC directives.
General| Power | 1200 W |
|---|---|
| No-load speed | 4800 rpm |
| Cutting depth at 45° | 45 mm |
| Max Cutting Depth at 45° | 45 mm |
| Motor Power | 1200 W |
| Max Cutting Depth at 90° | 65 mm |
To Next Page
