Excell PW User Manual

EXCELL PRECISION CO., LTD
PW Service Manual SME300000016
© Excell Precision Limited 2004. All rights reserved Worldwide.
The information contained herein is the property of Excell Precision Limited and is supplied
without liability for errors or omissions. No part may be reproduced or used except as
authorised by contract or other written permission. The copyright and the foregoing
restriction on reproduction and use extend to all media in which the information may be
embodied.

Excell PW Specifications

General

Brand	Excell
Model	PW
Category	Accessories
Language	English

Summary

INDICATOR HOUSING

RE-ASSEMBLY INSTRUCTIONS

Detailed steps for correctly reassembling the indicator housing to maintain IP rating.

BEFORE USING THE SCALE

INSTRUCTIONS FOR USE

Guidelines for safe and correct operation of the weighing scale.

PREPARING TO USE THE SCALE

Steps for setting up the scale on a suitable surface for accurate readings.

CHAPTER 1 INTRODUCTION

1-1 Features and Specifications

Overview of the weighing indicator's capabilities and technical specifications.

1-2 Scale Appearance

1-3 Power Supply

1-4 Display

1-5 Keyboard Function

1-6 Error Messages

1-7 Weight Units

CHAPTER 2 SERVICE MODE ACCESS

Capacity Configuration (01C5P)

Setting the weighing indicator's capacity and resolution parameters.

Weighing Calibration (02 CAL)

Procedure for calibrating the weighing indicator with known weights.

Function Setting (04 CFn)

Accessing and configuring various operational functions of the indicator.

2-1 Capacity Configuration

Weight Units Setting (CSP 01)

Setting specific weight units and their display parameters for the indicator.

Customised Weight Units Setting (CSP 02)

Configuring custom weight units and resolution limits for the indicator.

2-1-1 Weight Units Setting (CSP01)

2-1-2 Customised Weight Unit Setting (CSP 02)

2-1-3 Modify “Customized Weight Units” Setting

2-2 Weight Calibration (02 CAL)

2-2-1 Weight Calibration Setting (CAL01)

2-2-2 Manufacturing Location Gravity Setting (CAL02)

2-3 Linearity Adjustment (03 CLn)

2-4 Function Setting (04 CFn)

Environment Parameters (CFn 01)

Adjusting settings related to the operating environment for better performance.

Approval Configuration (CFn 02)

Setting up specific approval models and their associated configurations.

2-4-1 Environment Parameters (CFn 01)

2-4-2 Approval Configuration (CFn 02)

2-4-3 Keyboard Buzzer Type (CFn 03)

2-5 Gravity Zone Compensation (06 CGr)

CHAPTER 3 ADVANCED FUNCTIONS

3-1 Advanced Function Setting Table

A table listing available advanced functions and their corresponding display codes.

3-2 Advanced Function Setting Workflow

3-3 General Function Setting (01 FnC)

3-3-1 Automatic Backlight Function Setting (FnC 01)

3-3-2 Automatic Power-off Timer Setting (FnC 02)

3-3-3 HI/LO/OK Settings (FnC 03)

3-3-4 Restore to Default Settings (FnC 04)

3-3-5 Noise Filter Settings (FnC 05)

3-3-6 Hold Function Settings (FnC 06)

3-3-7 Auto Unit Weight Averaging Setting (FnC 07)

3-4 Weight Calibration (02 EC)

3-5 RS232 Serial Interface Settings (03 r51)

3-5-1 Baud Rate Settings (r5101)

3-5-2 Communication Protocol Settings (r5102)

3-5-3 Output Format Settings (r5103)

3-5-4 Continuous Transmission Settings (r5104)

3-5-5 Selection of the Continuous Transmission Rate (r5105)

3-5-6 Auto Transmission at Zero (r5106)

3-5-7 Reset Auto Transmission (r5107)

3-5-8 Output Condition Settings (r5108)

2 Command mode

Command Format A

List of host commands for controlling scale functions and modes.

Command Format B

List of host commands for reading weight and comparison data.

Command Format C

Command Format D

2 Output data format

Weight format

Structure of output data for Gross, Net, Tare, and other weight readings.

Simple format

Simplified output data structure for weight and comparison status.

Serial Data Transfer/Receive Format

Bit configurations for serial data transmission (start, parity, stop bits).

APPENDIX I: ASCII CODE TABLE

APPENDIX II: 7 SEGMENT DISPLAY CHARACTERS