Fargo HDP5000 User Manual

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP5000 High Definition Card Printer/Encoder User Guide (Rev. 1.3)
v
Changing to the Static IP Address Mode ______________________________________________ 6-20
Using the Clear Changes button _____________________________________________________ 6-22
Using the Media Information page _____________________________________________________ 6-23
Using the TCP/IP page ______________________________________________________________ 6-24
Using the TCP/IP page____________________________________________________________ 6-25
Using the Printer page_______________________________________________________________ 6-26
Using the System Log page___________________________________________________________ 6-28
Changing the Log Name___________________________________________________________ 6-29
Selecting the Log Type____________________________________________________________ 6-30
Selecting the Log Destination_______________________________________________________ 6-31
Setting up Email Event logging _____________________________________________________ 6-32
Specifying UDP Event logging _____________________________________________________ 6-33
Specifying TCP Event logging______________________________________________________ 6-35
Using the Administration pages _______________________________________________________ 6-37
Using the System Information page __________________________________________________ 6-37
Changing the Root Password _______________________________________________________ 6-39
Using the Reboot pages______________________________________________________________ 6-40
Rebooting the Printer _____________________________________________________________ 6-40
Upgrading the Main Firmware ______________________________________________________ 6-41
Using the Print Path page ____________________________________________________________ 6-45
Using the Help page ______________________________________________________________ 6-47
Additional Procedures ________________________________________________________6-47
Accessing the Ethernet Status LEDs____________________________________________________ 6-47
Reviewing the HDP5000 LED Table _________________________________________________ 6-47
Upgrading the Main Firmware with the Fargo Workbench Printer Utility _______________________ 6-48
Restoring the Factory Settings for Ethernet ______________________________________________ 6-50
Resetting the HDP5000 settings_____________________________________________________ 6-50
Changing the HDP5000 LCD Network Settings ________________________________________ 6-50
Accessing the Network Setup Menu__________________________________________________ 6-50
Changing the DHCP Setting________________________________________________________ 6-51
Changing the ANEG setting________________________________________________________ 6-51
Saving addresses_________________________________________________________________ 6-52
Resetting Passwords______________________________________________________________ 6-52
Accessing the HDP5000 IP Address _________________________________________________ 6-53
Ethernet Printer Troubleshooting Procedures_____________________________________6-54
Troubleshooting procedures ________________________________________________________ 6-54
Verifying the Printer Connection ____________________________________________________ 6-55
Verifying the Printer IP address _____________________________________________________ 6-55
Verifying that your PC can access the Printer using the ping command ______________________ 6-56
Printing a test page _______________________________________________________________ 6-57
Reviewing Frequently-asked Questions __________________________________________6-58
Glossary of Terms ____________________________________________________________6-65
Section 7: Card Lamination Module __________________________________________7-1
Safety Messages (review carefully)______________________________________________________ 7-2
Reviewing the Card Lamination Module _________________________________________________ 7-3
Installing the Card Lamination Module___________________________________________________ 7-4
Introduction _____________________________________________________________________ 7-4
Inspecting the Card Lamination Module _______________________________________________ 7-5
Unpacking the Card Lamination Module _______________________________________________ 7-5
Choosing a proper Location _________________________________________________________ 7-5
Preventing Moisture Condensation____________________________________________________ 7-5
Installing the Lamination Module Accessory____________________________________________ 7-6
Adjusting the Lamination Placement on the Card___________________________________________ 7-8

Fargo HDP5000 Specifications

General

Maximum resolution	300 x 300 DPI
Print speed (color)	7 card/h
Print speed (monochrome)	14 card/h
Product color	Black
Internal memory	16 MB
Total input capacity	100 sheets
Compatible operating systems	Windows 2000 / XP / Server 2003 / Vista (32 bit) Mac OS X v10.4 / v10.5 Linux

Weight and Dimensions

Weight	7300 g
Dimensions (WxDxH)	313 x 235 x 292 mm