EasyManuals Logo

FENDT 926 Vario User Manual

FENDT 926 Vario
267 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #260 background imageLoading...
Page #260 background image
260
TECHNICAL DATA
X X Check oil level of lifting shaft lubrication. Top up,
if necessary. (Only if leaking).
Oil level: Check using a measuring strip of about 40 mm straight
length.
Oil grade: Fendt Extra Trans 10W-40 or STOU SAE 10W-40 or
15W40.
5 Electrical, electronic systems
X X X Check battery acid level; if necessary top up
with distilled water. Not applicable to mainten-
ance-free batteries.
Level about 15 mm above top of plates. Open-circuit voltage with battery fully
charged 12.75 V.
X X X X Check lighting and signalling system and all
monitoring and warning systems for correct
operation. Read out up diagnostic memory and
remedy the faults.
Short circuit sensor. A fault message (symbol) must appear on the multiple display
accompanied by an intermittent audible signal.
X X X X Check software version and interconnection of
the electronic components and update if neces-
sary.
Complete tractor programming with end-of-line program - check interconnection.
6 Compressed air system
X X X X X Drain the water from the bottle. Pull cable to operate drainage valve.
as requi-
red
Check antifreeze level. Top up with antifreeze at temperatures below 5 °C.
Antifreeze: ethyl alcohol (X 902.015.003).
7 Assemblies / general
X X X X Check that bolted connections are firmly sea-
ted, especially on engine, transmission, front
axle, body and hydraulics; tighten if necessary.
Tighten hydraulic screw connections only in the
event of a leak. In particular, check steering and
front hydraulic hoses for chafing points.
Check for chafing points on hydraulic hoses, loose parts or missing protection de-
vices.
Switch off engine before tightening the pressure lines.
With front axle suspension, unload the pressure lines as well.
X X X X Check the trailer hitch. Swivel joint on trailer hitch: maximum play 3 mm.
X X X X Check and correct tyre pressure, if necessary. See technical data.
X X X X For lubrication of greasing points refer to Lubri-
cation chart, lubricate all joints.
Fendt Ultra lithium grease, Fendt Extra EP or multi-purpose grease, lithium-sapo-
nified, NLGI class 2 (worked penetration 265 - 295).
X X X X Test drive the tractor, checking braking effi-
ciency, adjust if necessary.
At 20 km/h, tractor must come to standstill within a stopping distance of 4 - 6 m.
No.
Services
regularly 1)
daily
Job Schedule
See also Operating Manual
Care and Maintenance
General notes and technical data, types of fluid and oil
Correct levels are determined by dipstick check or from the overflow at the
inspection hole.
Observe all accident prevention regulations and comply with directives for
handling and disposing of fluid and lubricants.
1.
50
2.
250
3.
500
4.
750
5.
1000
annu
al or
every
500
every 2
years
or
2000
operating hours

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the FENDT 926 Vario and is the answer not in the manual?

FENDT 926 Vario Specifications

General IconGeneral
Engine Power260 hp
TransmissionVario continuously variable transmission
Fuel Tank Capacity500 liters
Weight10, 500 kg
Engine type6-cylinder turbocharged
Rated engine speed2100 rpm
Displacement7.5 liters
Number of cylinders6
Maximum speed50 km/h
Tire OptionsMultiple options available

Related product manuals