Flowserve MASTER STATION IV EEP-SN4001 - Figure 7.34 - Restore Factory Defaults

64 pages

Save Page as PDF

To Next Page

To Previous Page

Limitorque

Master Station IV EEP-SN4001 FCD LMENIM5010-00-AQ – 03/19

7.2.7.7 Restore Factory Defaults

To return the MSIV conﬁguration settings to factory defaults, press the “Restore Factory Defaults” button at the bottom

of the File Manager menu. A conﬁrmation box will appear to conﬁrm the restoration. This action cannot be undone.

Figure 7.34 – Restore Factory Defaults

Main Page

Table of Contents3
Introduction6
Overview6
User Role Overview6
Figure 1.1 - Introduction7
Figure 1.2 - Enter User Name7
Figure 1.3 - Login7
Login7
Figure 1.4 - Main Menu8
Main Menu8
System Technical Data9
Function Flowchart10
Figure 2.1 - MSIV Functional Flowchart11
Quick Startup13
Figure 4.1 - MSIV Rear Panel Electrical Connections14
Electrical Connections14
MSIV Rear Panel Connections14
Master Stationi V EEP-SN4001 FCD LMENIM5010-00-AQ - 03/1915
Figure 4.2 - Debug Port Connection: DB9 Male15
Table 4.1 - Network Channel a Connection15
Table 4.2 - Network Channel B Connection15
Figure 4.3 - DCS Serial Port Connection: DB9 Female16
Master Station Wiring Requirements17
Figure 4.4 - Modbus Redundant Loop Topology18
Master Station Network Topologies18
Table 4.3 - Hot-Standby Wiring Connections for Redundant Modules19
Figure 5.1 - the Main Menu Screen20
System Status20
Main Menu20
Figure 5.2 - System Status21
Figure 5.3 - Network Status21
System Status21
Network Status21
Figure 5.4 - MOV Status Screen22
Figure 5.5 - MSIV Module Status22
MOV Status22
MSIV Status22
Figure 5.6 - MOV Data23
MOV Data23
Figure 6.1 - System Control Menua24
System Control24
Main Menu24
Figure 6.2 - MOV Control Menu25
Figure 6.3 - Control Relays25
MOV Control25
Figure 6.4 - Emergency Shutdown26
Figure 6.5 - Emergency Shutdown in Progress26
Emergency Shutdown26
Figure 6.6 - Emergency Shutdown Termination27
Figure 7.1 - System Configuration Menu28
System Configuration28
Main Menu28
Figure 7.2 - System Settings Menu29
System Settings29
Figure 7.3 - Software Version Information30
Figure 7.4 - Language Selection Menu30
Figure 7.5 - System Clock Settings31
Figure 7.6 - Time Zone Settings31
Redundant Configuration32
Figure 7.7 - Screen Saver Settings32
Figure 7.8 - Redundant Configuration Menu32
Change MOV Tags33
Figure 7.9 - Configuration Transfer Lockout33
Figure 7.10 - MOV Tag List33
User Administration34
Figure 7.11 - User Administration Menu34
Figure 7.12 - Delete User Menu34
Figure 7.13 - User Settings Menu35
Figure 7.14 - Change Password Menu35
DCS Configuration36
Figure 7.15 - DCS Configuration Menu36
Figure 7.16 - Configure DCS Serial Port36
Figure 7.17 - Configure DCS Ethernet Port37
Figure 7.18 - Configure DCS Data Table Menu37
Table 7.1 - Status Bit Definitions38
Figure 7.19 - FC 02 Read Input Status38
Table 7.2 - Function Code 02 Example Message Breakdown40
Figure 7.21 - FC 03 Example Data Table41
Figure 7.20 - FC 03 Read Holding Registers Menu41
Table 7.3 - Function Code 03 Example Message Breakdown42
Table 7.4 - Function Code 03 Holding Registers42
Figure 7.22- Modbus FC 05/15 Coils44
Figure 7.23 - FC 05/15 Sample Data Table45
Table 7.5 - DDC Coil Assignments, Modbus 05 Command Usage for Digital Outputs45
Table 7.6 - Function Code 05 Example Message Breakdown46
Table 7.7 - Function Code 15 Example Message Breakdown46
Figure 7.24 - Modbus Holding Registers - One Per MOV Shown47
Figure 7.25 - FC 06 Sample Data Table with "Two Per Mov" Selected47
Table 7.8 - Function Code 06 First Command Message Breakdown48
Table 7.9 - Function Code 06 Message Breakdown48
Table 7.10 - Function Code 06 Message Breakdown49
Table 7.11 - Function Code 16 Message Breakdown49
Table 7.12 - Valid Command Register Operations50
Figure 7.26 - General DCS Settings (Defaults Shown)51
Figure 7.27 - MOV Network Configuration52
Figure 7.28 - Active Movs52
MOV Network Configuration52
Figure 7.29 - Polling Priority, Active Movs53
Figure 7.30 - File Manager Menu53
File Manager53
Figure 7.31 - Import Configuration File54
Figure 7.32 - Export Event Log55
Figure 7.33 - Update Software Menu55
Figure 7.34 - Restore Factory Defaults56
Figure 8.1 - Main Menu57
Diagnostics57
Main Menu57
Figure 8.2 - Diagnostics Menu58
Figure 8.3 - Event Log58
Diagnostics58
Figure 8.4 - Comm/Fc Logger59
Figure 8.5 - Debug Serial Port59
Figure 8.6 - Polling Statistics60
Troubleshooting Guide61
Front Panel Indicators61
Network Status Screen61
Figure 9.1 - Rear Panel On/Off Switch, Fuse, and Power Input Terminals62
Blank Display62
Network Communications62

Flowserve MASTER STATION IV EEP-SN4001 - Figure 7.34 - Restore Factory Defaults

Table of Contents

Related product manuals