Fluke endurance series

To Next Page

To Previous Page

Endurance

Series

Users Manual, Rev. 2.0, Jun 2020

Emissivity

all models 0.100 to 1.100, in 0.001 increments

Slope

all 2C models 0.850 to 1.150, in 0.001 increments

Signal Processing

All models Averaging, peak hold, valley hold, advanced peak hold, advanced valley hold,

ambient background temperature compensation

Main Page

Table of Contents3
List of Tables8
List of Figures9
Compliance Statement12
Safety Information13
Contacts16
1 Description17
- Table 1-1: Model Overview17
2 Technical Data18
- Measurement Specification18
- Optical Specifications21
- Electrical Specifications23
- Environmental Specifications24
- Dimensions25
- Figure 2-1: Dimensions25
- Scope of Delivery26
3 Basics27
- Measurement of Infrared Temperature27
- Emissivity for 1-Color Measurements27
- Theory for 2-Color Measurements28
4 Environment30
- Ambient Temperature30
- Atmospheric Quality30
- Electrical Interference30
- Figure 4-1: One Earth Ground at the Sensor (Left) or at the Power Supply (Right)30
5 Installation31
- Distance to Object31
- Positioning31
- Figure 5-3: Acceptable Sensor Viewing Angles33
- Viewing Angles33
- Aiming and Focusing34
- Figure 5-4: Sensor Eyepiece and Reticle34
- Electrical Installation35
- Inputs37
  - Trigger37
  - Analog Input37
- Figure 5-10: Principle of Background Temperature Compensation38
- Outputs39
6 Operation42
- Control Panel42
- Menu Structure44
- Post Processing55
7 Rs48560
- Specification60
- Installation60
- Figure 7-1: Network in Linear Topology (Daisy Chain)60
- Wiring61
- Computer Interfacing61
- Figure 7-2: RS485 Communication61
- Figure 7-3: Wiring the Sensor's RS485 Interface with USB/RS485 Converter61
- Multiple Sensors62
- Figure 7-4: Wiring Multiple Sensors Via RS485 Interface with USB/RS485 Converter62
8 Ethernet63
- Addressing63
  - Advanced Address Settings63
  - Figure 8-1: Command Prompt Window63
- PC Network Adapter64
- ASCII Programming65
- Http Server65
- Figure 8-2: Web Page65
- Video Streaming66
9 Profinet Io67
- Configuration67
- Parameters67
- Messages68
- Table 9-1: Pyrometer Parameters68
- Table 9-2: Messages68
- Input Data69
- Output Data69
- Diagnostics69
- Table 9-3: Input Data69
- Table 9-4: Output Data69
- Table 9-5: Parameter Types69
- Table 9-6: Error Codes70
10 Ethernnet/Ip71
- Configuration71
- Parameters71
- Input Data72
- Table 10-1: Pyrometer Parameters72
- Table 10-2: Input Data72
- Output Data73
- Diagnostics73
- Table 10-3: Output Data73
- Table 10-4: Parameter Types73
- Table 10-5: Error Codes74
11 Options75
- Figure 11-1: Laser Indication76
- Laser Sighting (-L)76
- Figure 11-2: LED Spot Size Indication77
- LED Sighting (-D)77
- Video Sighting (-V)77
- Air/Water-Cooled Housing78
- Figure 11-3: Air/Water-Cooled Housing78
- Avoidance of Condensation79
- Table 11-1: Minimum Device Temperatures [°C/°F]80
- Manufacturer's Calibration Certificate81
12 Accessories82
- Electrical Accessories82
- Mechanical Accessories96
13 Maintenance115
- Troubleshooting Minor Problems115
- Fail-Safe Operation115
- Table 13-1: Troubleshooting115
- Table 13-2: Fail-Safe Error Codes116
- Table 13-3: Error Codes for Analog Output116
- Window Cleaning118
- Window Exchange119
14 Ascii Programming120
- Remote Versus Manual Settings120
- Command Structure120
- Transfer Modes121
- Sensor Information121
- Sensor Setup122
- Sensor Control123
  - Analog Output123
  - Relay Output123
- RS485 Communication123
- Multidrop Mode123
- Command List125
15 Appendix130
- Optical Diagrams130
- Spot Size Calculator140
- Figure 15-31: Spot Size Calculator140
- Determination of Emissivity141
- Typical Emissivity Values141
- Determination of Slope145
- Signal Reduction146
- Figure 15-32: Model E1RH - Allowed Signal Reduction over Target Temperature146
- Figure 15-33: Model E1RL - Allowed Signal Reduction over Target Temperature146
- Figure 15-34: Model E2RL - Allowed Signal Reduction over Target Temperature147

Fluke endurance series - Page 20

Table of Contents

Related product manuals