Flyer Mountain - Environmental Protection Tips

77
EN
22. Wearing parts
Your FLYER is a technical product and therefore
requires regular inspection.
Many parts of your FLYER are subject to very
rapid wear, depending on their function and the
extentofusage.
This includes:
• Tyres
• Brake pads
• Brake discs
• Bicycle chain or drive belt
• Chain wheels, sprockets, jockey wheels
• Lighting system
• Handlebar grips
• Lubricants
• Gear and brake cables
• Bearings
• Suspension elements
Have your FLYER regularly inspected in
a FLYER specialised workshop and
have wearing parts replaced as re-
quired. Regular visual inspection for
cracks, scratches and damage to com-
ponents is the responsibility of the rider.
As is the case with all mechanical com-
ponents, the bicycle is subject to wear
and tear and high stress. Depending on
the degree of stress imposed on them,
di󰀨erent materials and parts may react
di󰀨erentlyintermsofwearandfatigue.A
part may suddenly fail and cause injuries
to the rider when its intended service life
isexceeded.
Any kind of cracks, scratches or colour
changes in high-stress areas are an in-
dicator that the service life of the com-
ponent has been exceeded and that it
should be replaced.
23. Generalwarranty
23.1 Generaldealer’swarranty
End customers shall be entitled to exercise the
standard warranty claims against the FLYER
dealer (depending upon the agreement or ap-
plicable law; as a rule two years after delivery).
For the battery, a residual capacity of 60 % of
the original rated capacity after two years or 500
full charging cycles is guaranteed, provided that
the battery has been operated and charged in
accordance with the operating instructions. Nor-
mal wear and tear is generally not covered by the
warranty. The end customer shall be responsible
for ensuring that the FLYER e-bike is regularly
maintained and cared for (including the conduct
of all inspections according to the operating in-
structions).Warrantyclaimsshallalsobeexclud-
edintheeventthattheFLYERe-bikeismodied
or repaired independently or used other than for
its intended purpose: racing and competition,
commercial usage, overloading, and other use
thatdoesnotreecttheintendedpurpose.
The warranty period for used bicycles from
FLYER dealers (second-hand bicycles) shall start
fromthedateofpurchasebytherstbuyer.
23.2 FLYERAGmanufacturer’s
warranty
The services under the warranty can be found in
the service booklet or on our website at:
https://www.yer-bikes.com/garantie.
24. Inspection plan
After the rst 200 ridden kilometres or after 4
months:
FLYER specialist retailer
• Checkthermattachmentofallscrews,nuts
and quick-release fasteners
• Check the wheels and centre them as
required
• Check the tyres
• Check the fastening torque on all parts
• Adjust the headset
• Check the brake lines and shifter cables
• Check the gear system and adjust if neces-
sary
• Check the brakes and adjust if necessary
• Su󰀩cientlubricationofallcomponents
• Check the suspension elements and adjust if
necessary
•
FLYER rider
Duringyoure-bike'srstinspectionbytheFLYER
specialistretailer,askthemtoexplainthecorrect
processes for cleaning and oiling the chain after
rain and checking components for function or
damage.
Beforeeachride–FLYERrider
• Check the correct position of the bell
• Check the function of the brakes
• Check the function of the gear system
• Are all quick-release fasteners, quick-release
axles,screwsandnutscompletelyclosedand
fastened?
• Check that the tyre pressure is correct
• Check the wheels for true running and dam-
age as well as safe attachment and correct
fastening