Fuji Electric FLD-1 - 15. REPLACEMENT OF BUILT-IN BATTERY

189 pages

To Next Page

To Previous Page

INF-TN1FSC-E 155

15. REPLACEMENT OF BUILT-IN BATTERY

(1) Turn off the power supply of main unit.

(2) Remove the rubber guard.

(3)

Locate 4 screws at the corners of the back cover diagram label.

Remove the 4 screws and caver as shown.

(4) Remove the battery and replace it with the approriate service part.

Note) Install a combination of the main unit side terminal and the battery side terminal.

→ →

• Do not give the equipment a shock

• Do not disassemble or modify the equipment

• Do not use the equipment with the built-in battery removed..

CAUTION

Main Page

PREFACE2
CONTENTS3
WARNING SYMBOLs AND THEIR MEANINGS6
SAFETY PRECAUTIONS7
1. OVERVIEW10
2. CHECK OF DELIVERED ITEMS11
- 2.1 On purchase of flow transmitter (type: FSC)11
- 2.2 On purchase of detector (type: FLD)12
- 2.3 On purchase of flow velocity distribution measurement detector (type: FSD)13
3. CHECK MODEL AND SPECIFICATION14
4. NAME AND EXPLANATION OF EACH PART17
- 4.1 Name and explanation of main unit and detector17
- 4.2 Explanation of keys19
- 4.3 Handling of SD memory card20
5. POWER ON AND POWER OFF25
- 5.1 Operating power supply25
- 5.2 Turning on the power and language preference26
- 5.3 Power OFF27
6. WIRING28
- 6.1 Diagram28
- 6.2 Connection of dedicated cables28
- 6.3 Connection of analog input/output cable(4 to 20 mA DC)29
- 6.4 Connection of USB cable29
7. INPUT OF PIPING SPECIFICATIONS30
- 7.1 Display of pipe setup screen30
- 7.2 Entry of site name (not required measurement)33
- 7.3 Outer diameter of piping (unit: mm)(range: 13 to 6000 mm)36
- 7.4 Piping material37
- 7.5 Wall thickness (unit: mm) (range: 0.1 to 100.00mm)38
- 7.6 Lining material39
- 7.7 Lining thickness (unit: mm) (range: 0.01 to 100.00 mm)40
- 7.8 Kind of fluid41
- 7.9 Viscosity42
- 7.10 Selection of sensor mounting method43
- 7.11 Kind of sensor44
- 7.12 Transmission voltage (used when an indicator is 1 or less during measurement)45
- 7.13 Completion of PROCESS SETTING46
8. MOUNTING OF DETECTOR47
- 8.1 Selection of mounting location47
- 8.2 Selection of detector50
- 8.3 Use of surface-treated accessories52
- 8.4 How to mount small size (standard) sensor and small outer diameter sensor to pipe53
  - 8.4.1 How to mount a sensor (V method)53
  - 8.4.2 How to mount a small size (standard) sensor (Z method)54
- 8.5 How to mount large and medium size sensor56
- 8.6 How to mount high temperature sensor to pipe63
  - 8.6.1 How to mount a sensor (V method)63
  - 8.6.2 How to mount a sensor (Z method)64
- 8.7 How to fold gage paper (used for determining mounting position)66
9. START MEASURING67
10. Setting Operation (Application)72
- 10.1 How to use SITE SETUP function (SITE SETUP page)73
- 10.2 Setting of data logger function85
- 10.3 Setting of system (SYSTEM SETUP screen)97
- 10.4 Setting of range (setting screen for input/output range)115
  - 10.4.1 Setting the input range: When setting the range for the input current or input voltage.Setting range: 0.000 to ±9999999999115
  - 10.4.2 Setting the output range117
- 10.5 Use of printer function (PRINTER screen)121
- 10.6 Maintenance function (MAINTENANCE screen)126
- 10.7 Flow velocity distribution display function (optional)139
  - 10.7.1 Installing Detector139
  - 10.7.2 Operation144
- 10.8 Contents of errors in status display149
  - 10.8.1 How to check status display149
  - 10.8.2 Action on error150
11. MAINTENANCE AND CHECKUP153
12. ERROR AND REMEDY155
- 12.1 Error in LCD Display155
- 12.2 Error of key155
- 12.3 Error in measured value156
- 12.4 Error in analog output159
13. EXTERNAL COMMUNICATION SPECIFICATION160
14. HOW TO USE PRINTER161
- 14.1 How to connect printer161
- 14.2 How to load printer roll sheet163
15. REPLACEMENT OF BUILT-IN BATTERY164
16. APPENDIX165
- 16.1 Piping data165
- 16.2 Command tree173
- 16.3 Specifications175
- 16.4 Q & A180
- 16.5 File contents of SD memory card185

Fuji Electric FLD-1 - 15. REPLACEMENT OF BUILT-IN BATTERY

Table of Contents

Related product manuals