HP 8712ES - Page 505

Index
Index 11
Set Track Frequency key, 8-81
Set Year key
, 8-81
setting HP-IB addresses
, 1-14
setting the line voltage
, 1-4
setting up the analyzer
, 1-10
shift spurs
, 5-13
shipment contents
, 1-3
shipping instructions
, 10-4
Short key
, 8-81
short, calibration standard
, 6-
26
, 8-81
Show Clock on Line 1 key
, 8-82
Show Clock on Line 2 key
, 8-82
SICL LAN Setup key
, 8-82
signal detection
, 3-5
signal path icon
, 3-7
Single key
, 8-82
single point limits
, 4-32
Smith Chart key
, 8-82
Smith chart markers
, 4-27
Smith Chart Z0 key
, 8-82
Socket Port No. key
, 8-82
softkey auto-step
, 4-62
Softkey Auto-Step key
, 8-83
source power, entering
, 2-6
Space key
, 8-83
Span key
, 2-6, 8-83
S-parameter measurements,
calibration example
, 3-20
S-parameters
explanation
, 3-9
measuring
, 3-9
numbering convention
, 3-9
specifications
, 9-1, 9-2
definitions
, 9-2
features
, 9-45
general information
, 9-39
system performance, corrected,
50 ohm
2-port cal
, 9-3
T/R cal
, 9-9
system performance, corrected,
75 ohm
2-port cal
, 9-7
T/R cal
, 9-15
system performance,
uncorrected
50 ohm
, 9-21
75 ohm
, 9-22
test port input
, 9-29
test port output
, 9-23
speed increase of sweep
, 5-3
speed with hardcopy
, 4-82
Split Disp FULL split key
, 8-83
split display
, 2-8, 4-46
Spur Avoid key
, 8-83
Spur Avoid Options key
, 8-84
spur avoidance
, 5-8, 5-13
SRL key
, 8-84
Stack Size key
, 8-84
standard deviation
, 4-18
standards, calibration
, 6-26
standby
, 7-19
start frequency, change to
increase sweep speed
, 5-4
Start key
, 2-6, 8-84
Start Line # key
, 8-84
Start Power key
, 8-84
static-safe equipment
part numbers
, 1-8
statistical mean, marker limit
test
, 4-33
Statistics key
, 8-85
statistics, marker
, 4-18
statistics, peak-to-peak
, 4-33
Step key
, 8-85
Step Sweep on OFF key
, 8-85
Stop key
, 2-6, 8-85
Stop Power key
, 8-85
stop printer
, 8-5
Store CC To Disk key
, 8-85
Store CC To EPROM key
, 8-86
storing measurement results
, 4-
55
Subnet Mask key
, 8-86
swap equal adapters method of
calibration
, 3-25
SWEEP key
, 8-86
Sweep Out key
, 8-86
sweep speed
increase start frequency
, 5-4
increasing
, 5-3
reducing averaging
, 5-5
reducing number of points
, 5-5
turning off alternate sweep
, 5-
7
turning off spur avoidance
, 5-8
using auto mode
, 5-4
viewing single measurement
channel
, 5-6
Sweep Time AUTO man key
, 8-
86
Sweep Time key
, 8-86
switch
line voltage selector
, 1-4
power
, 7-19
Switching Test Set key
, 8-87
SWR key
, 8-87
symbol, instruction manual
, 10-
5
symbols and markings
instrument
, 10-5
Sync Green on OFF key
, 8-87
synchronization of external
monitor
, 4-89
sync-on-green capability
, 4-89
system bandwidth
, 5-10
changing
, 5-12
how it works
, 5-10
System Bandwidth key
, 8-87
System Config key
, 8-88
System Controller key
, 8-88
system impedance
, 3-12
system lock-up, how to recover
,
8-66
SYSTEM OPTIONS key
, 8-88
system performance,
specifications
, 9-3