HP 8921A - Page 567

Index
567
input, RF analyzer, 90, 421
input, spectrum analyzer, 461
manual control, 90, 421, 461
attenuator
decoder interference, 103, 421
input, 90, 421, 461
oscilloscope interference, 103, 421
attenuator hold, 291, 434, 444
Audio Analyzer Screen
AM Depth, 99, 419
Audio Frequency Analyzer screen
Distortion, 100
audio frequency counter
gate time, 98
sampling, 98
audio frequency generator, 442
audio frequency measurements, 59, 98,
106, 289, 424, 436, 446, 499
AUDIO IN connector
avoiding damage to, 509
description, 509
for ac level measurement, 97, 431, 442
for ac level measurements, 59
for call processing, 116
for external load resistancemeasure-
ment, 102, 444
for SNR operation, 98, 106, 289, 436,
446, 499
AUDIO IN HI connector, 509
Audio In Lo
AF Analyzer screen, 99
AUDIO IN LO connector
600 ohm impedance, 99, 509
floating, 99, 509
grounded, 99, 509
AUDIO MONITOR OUTPUT connector
description, 510
Audio Out
Duplex Test screen, 292
RF Generator screen, 434
Signaling Encoder screen, AMPS-
TACS mode, 302
Signaling Encoder screen, CDCSS
mode, 315
Signaling Encoder screen, Digi Page
mode, 320
Signaling Encoder screen, DTMF
mode, 325
Signaling Encoder screen, EDACS
mode, 329
Signaling Encoder screen, Func Gen
mode, 340
Signaling Encoder screen, LTR mode,
343
Signaling Encoder screen, NAMP-
NTAC mode, 302
Signaling Encoder screen, NMT mode,
370
Signaling Encoder screen, Tone Seq
mode, 378
AUDIO OUT connector
coupling, 292, 302, 315, 320, 325, 329,
340, 343, 370, 378, 434
description, 510
audio power
measurement, 97, 431, 442
audio source, 218, 226, 231, 235, 241,
247, 251, 263, 281
Auto All
Range Hold, 208
Auto/Norm
Oscilloscope screen, 396
automatic level control, 107
autoranging
AF/RF measurements, 208
gain setting, 103
input attenuator, 103, 421
Autostart Test Procedure on Power-Up
Tests (ExecutionConditions) screen,
482
auto-tuning
AF/RF measurements, 208
RF, 92, 297, 425, 504
averaging
example, 69
measurement results, 69
restart averaging, 69
AVG, 69, 527
B
B/I Delay (FOCC)
Signaling Encoder screen, AMPS-
TACS mode, 303
Signaling Encoder screen, NAMP-
NTAC mode, 303
backspace key, 529
bandwidth
adjacent channel power, 88
IF filter, 295, 421, 502
resolution, ACP measurement, 92
Base Freq
Configure screen, 203
base settings
changing, 74
default, 74
base station receiver
simulating, AMPS-TACS/NAMPS-
NTACS, 217
basic operation, 53
Batt Save
Signaling Encoder screen, NMT mode,
370
battery, 51
saving, 370
baud rate, 387
beat frequency, 62
Beeper
Configure screen, 51, 204
beeper
error alert, 204
volume control, 51, 204
Bell
radio standard, 326
bias
dc, offsetting, 434
billing information, 375
bit error, 320
bits
CDCSS data rate, 227
CDCSS data stream, 318
CDCSS sequence, 227
digitial paging data rate, 232
dotting, 306, 308
information, 306, 308
LTR data rate, 252
message, 225
NMT data rate, 371