What to do if my HP Server has problems during initial operation?
If your HP Server experiences problems during initial operation, remove any add-in or optional components and then retest the server to see if the issue is resolved.
How to fix installation failures due to damage in HP rp3440 Server?
If you experience installation failures in your HP Server due to damage during transit, reseating the connectors might resolve problems resulting from rough handling.
What to do if I have compatibility problems or incorrect installations in HP rp3440?
If you are facing compatibility problems or incorrect installations in your HP Server, ensure that all components are correctly installed and that all connectors are fully engaged.
General| Form Factor | Rack-mountable |
|---|---|
| Processor Speed | Up to 1.0 GHz |
| Memory | Up to 32 GB |
| RAID | Optional |
| Memory Type | DDR SDRAM |
| Storage | SCSI |
| Network | Dual Gigabit Ethernet |
| Power Supply | Redundant |
| Operating System | HP-UX, Linux, Windows |
| Expansion Slots | PCI |
Identifies the target readers for this document, including service providers and administrators.
Outlines the structure of the guide, listing each chapter and its scope.
Explains the formatting conventions used in the document for clarity.
Lists essential information to have ready before contacting HP support.
Provides contact details and methods for obtaining HP technical support.
Illustrates the front, rear, and pedestal views of the HP 9000 rp3410 and rp3440 servers.
Provides detailed information about the server's core features and components.
Details minimum and maximum configuration options for the servers.
Lists the physical dimensions and weight specifications for the servers.
Covers electrical requirements, including power cables and circuit breaker sizes.
Details the power supply ratings, input voltage, and current specifications.
Provides environmental requirements such as temperature, humidity, and noise levels.
Illustrates the physical layout and external views of the servers.
Provides a step-by-step checklist for successful server installation.
Details procedures for unpacking, inspecting for damage, and checking inventory.
Guides on installing extra hardware components like drives, memory, and cards.
Provides instructions for installing additional internal hard disk drives.
Details the procedure for installing a DVD drive behind the front bezel.
Guides on installing DDR SDRAM memory modules into the server's sockets.
Explains how to remove and replace the removable PCI card cage.
Provides instructions for installing PCI and graphics cards into the server.
Details how to install a second power supply for redundant capability.
Guides on installing dual processor modules onto the system board.
Provides instructions for replacing the system battery.
Describes how to connect power and LAN cables to the server.
Guides on setting up and starting a console session for server management.
Identifies the HP-UX 11i version 1 and higher as the supported OS.
Describes procedures for booting and shutting down the HP-UX operating system.
Outlines a systematic approach to diagnosing and resolving server issues.
Provides guidance on troubleshooting issues related to system power.
Details how to use online tools like STM and EMS for troubleshooting.
Explains how to use the Offline Diagnostic Environment (ODE) for troubleshooting.
Describes how to identify hardware issues using system LEDs and SEL.
Explains how to interpret system LEDs for hardware problem diagnosis.
Provides crucial safety precautions for handling components and the server.
Illustrates the internal layout, showing component and connector locations.
Guides on removing and replacing server chassis covers and bezels.
Details the procedure for removing and replacing system fans.
Provides instructions for removing and replacing the server's power supply.
Guides on removing and replacing internal hot-pluggable hard disk drives.
Explains how to remove and replace processor and memory airflow guides.
Details the procedure for removing and replacing system memory modules (DIMMs).
Guides on removing and replacing dual processor modules.
Provides instructions for removing and replacing the system battery.
Explains how to remove and replace the PCI card cage.
Guides on removing and replacing PCI and graphics cards.
Details the procedure for removing and replacing the PCI backplane.
Guides on removing and replacing removable media drives like DVD.
Explains how to remove and replace the iLO MP card.
Provides instructions for removing and replacing the iLO MP card battery.
Guides on removing and replacing the LED status panel.
Details the procedure for removing and replacing the system board.
Explains how to remove and replace the power supply interface module.
Guides on removing and replacing the hard disk drive SCSI backplane.
Provides visual identification of server parts for replacement.
Explains the customer self-repair program and part categories.
Lists part numbers for customer self-repair units and components.
Describes the BCH utility for firmware interaction and system parameter management.
Lists and explains the types of commands available in the BCH interface.
Details commands for viewing and modifying system configuration settings.
Describes commands for viewing system configuration and state information.
Lists commands for service personnel to view system service information.
Provides an overview of the Integrated Lights-Out Management Processor (iLO MP).
Summarizes temperature, airflow, weight, and dimension data for server configurations.
To Next Page
