To Next Page

To Previous Page

# Configure VLAN 4092 as the primary control VLAN of RRPP domain 1.

[DeviceA-rrpp-domain1] control-vlan 4092

# Configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device A as the master node of primary ring 1, with Ten-GigabitEthernet 1/0/1 as

the primary port and Ten-GigabitEthernet 1/0/2 as the secondary port. Enable ring 1.

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port ten-gigabitethernet

1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# Enable RRPP.

[DeviceA] rrpp enable

2. Configure Device B:

# Create VLANs 1 through 30.

<DeviceB> system-view

[DeviceB] vlan 1 to 30

# Map these VLANs to MSTI 1.

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 1 to 30

# Activate the MST region configuration.

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on Ten-GigabitEthernet

1/0/1.

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] link-delay 0

# Disable the spanning tree feature on the port.

[DeviceB-Ten-GigabitEthernet1/0/1] undo stp enable

# Configure the port as a trunk port.

[DeviceB-Ten-GigabitEthernet1/0/1] port link-type trunk

# Assign the port to VLANs 1 through 30.

[DeviceB-Ten-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceB-Ten-GigabitEthernet1/0/1] quit

# Configure Ten-GigabitEthernet 1/0/2 in the same way Ten-GigabitEthernet 1/0/1 is

configured.

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] link-delay 0

[DeviceB-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceB-Ten-GigabitEthernet1/0/2] quit

# Configure Ten-GigabitEthernet 1/0/3 in the same way Ten-GigabitEthernet 1/0/1 is

configured.

[DeviceB] interface ten-gigabitethernet 1/0/3

[DeviceB-Ten-GigabitEthernet1/0/3] link-delay 0

[DeviceB-Ten-GigabitEthernet1/0/3] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/3] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30

Other manuals for HPE FlexFabric 5700 Series

Network Management And Monitoring Configuration Guide314 pages

Questions and Answers:

Need help?

Do you have a question about the HPE FlexFabric 5700 Series and is the answer not in the manual?

HPE FlexFabric 5700 Series Specifications

General

Product Line	HPE FlexFabric
Model	5700 Series
Power Supply	Redundant power supply options
Layer Support	Layer 2/3
Management	HPE Intelligent Management Center (IMC), CLI, SNMP
Routing Protocol	RIP, OSPF, BGP, IS-IS
Features	Virtualization
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1w, IEEE 802.1s, IEEE 802.3ad, IEEE 802.3ae
Operating Temperature	32°F to 113°F (0°C to 45°C)
Operating Humidity	10% to 90% (noncondensing)
Latency	Less than 1 µs