To Next Page

To Previous Page

# Create VLANs 11 and 12.

<DeviceC> system-view

[DeviceC] vlan 11 to 12

# Map VLAN 11 to MSTI 1 and VLAN 12 to MSTI 2.

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 11

[DeviceC-mst-region] instance 2 vlan 12

# Activate the MST region configuration.

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on Ten-GigabitEthernet

1/0/1.

[DeviceC] interface ten-gigabitethernet 1/0/1

[DeviceC-Ten-GigabitEthernet1/0/1] link-delay 0

# Disable the spanning tree feature on the port.

[DeviceC-Ten-GigabitEthernet1/0/1] undo stp enable

# Configure the port as a trunk port.

[DeviceC-Ten-GigabitEthernet1/0/1] port link-type trunk

# Remove the port from VLAN 1, and assign it to VLANs 11 and 12.

[DeviceC-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/1] port trunk permit vlan 11 12

# Configure VLAN 11 as the default VLAN.

[DeviceC-Ten-GigabitEthernet1/0/1] port trunk pvid vlan 11

[DeviceC-Ten-GigabitEthernet1/0/1] quit

# Configure Ten-GigabitEthernet 1/0/2 in the same way Ten-GigabitEthernet 1/0/1 is

configured.

[DeviceC] interface ten-gigabitethernet 1/0/2

[DeviceC-Ten-GigabitEthernet1/0/2] link-delay 0

[DeviceC-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/2] port trunk permit vlan 11 12

[DeviceC-Ten-GigabitEthernet1/0/2] port trunk pvid vlan 11

[DeviceC-Ten-GigabitEthernet1/0/2] quit

# Set the physical state change suppression interval to 0 seconds on Ten-GigabitEthernet

1/0/3.

[DeviceC] interface ten-gigabitethernet 1/0/3

[DeviceC-Ten-GigabitEthernet1/0/3] link-delay 0

# Disable the spanning tree feature on the port.

[DeviceC-Ten-GigabitEthernet1/0/3] undo stp enable

# Configure the port as a trunk port.

[DeviceC-Ten-GigabitEthernet1/0/3] port link-type trunk

# Remove the port from VLAN 1, and assign it to VLAN 12.

[DeviceC-Ten-GigabitEthernet1/0/3] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/3] port trunk permit vlan 12

# Configure VLAN 12 as the default VLAN.

[DeviceC-Ten-GigabitEthernet1/0/3] port trunk pvid vlan 12

[DeviceC-Ten-GigabitEthernet1/0/3] quit

Other manuals for HPE FlexFabric 5700 Series

Network Management And Monitoring Configuration Guide314 pages

Questions and Answers:

Need help?

Do you have a question about the HPE FlexFabric 5700 Series and is the answer not in the manual?

HPE FlexFabric 5700 Series Specifications

General

Product Line	HPE FlexFabric
Model	5700 Series
Power Supply	Redundant power supply options
Layer Support	Layer 2/3
Management	HPE Intelligent Management Center (IMC), CLI, SNMP
Routing Protocol	RIP, OSPF, BGP, IS-IS
Features	Virtualization
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1w, IEEE 802.1s, IEEE 802.3ad, IEEE 802.3ae
Operating Temperature	32°F to 113°F (0°C to 45°C)
Operating Humidity	10% to 90% (noncondensing)
Latency	Less than 1 µs