EasyManuals Logo

InFocus IN5122 User Manual

InFocus IN5122
97 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #91 background imageLoading...
Page #91 background image
89
Troubleshooting
Regarding the indicator lamps
When the LAMP, TEMP and POWER indicator operate differently than usual,
follow the instructions below in the following table.
For the SECURITY indicator, see SECURITY INDICATOR in the SECURITY menu.
POWER
indicator
LAMP
indicator
TEMP
indicator
Description
Solid
Orange
Turned
off
Turned
off
The projector is in a standby state.
Please refer to the section “Power on and off”.
Blinking
Green
Turned
off
Turned
off
The projector is warming up.
Please wait.
Solid
Green
Turned
off
Turned
off
The projector is in an on state.
Ordinary functions can be performed.
Blinking
Orange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
Blinking
Red
(discre-
tionary)
(discre-
tionary)
The projector is cooling down. An error has
been detected.
Please wait until POWER indicator nishes blinking,
and then follow the associated instructions below.
Blinking
Red
or
Solid
Red
Solid
Red
Turned
off
The lamp will not light, and the projector may be
overheating.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufciently cooled down, please conrm the following
items, and then turn the power on again.
Are the air vents blocked?
• Is the air lter dirty?
• Is the room temperature higher than 95°F (35°C)?
If the same indicator re-appears after xing the above,
please change the lamp referring to the section
Replacing the lamp.
Blinking
Red
or
Solid
Red
Blinking
In Red
Turned
off
The lamp cover has not been properly xed.
Please turn the power off, and allow the projector
to cool down at least 45 minutes. After the projector
has sufciently cooled down, please verify that the
lamp cover is securely and properly fastened. After
performing any needed maintenance, turn the power on
again.
If the same indicator re-appears after xing the
above,
please contact your dealer or service company.
Blinking
Red
or
Solid
Red
Turned
off
Blinking
Red
The cooling fan is not operating.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufciently cooled down, please conrm that no foreign
matter has become caught in the fan, etc., and then
turn the power on again.
If the same indicator re-appears after xing the above,
please contact your dealer or service company.

Other manuals for InFocus IN5122

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the InFocus IN5122 and is the answer not in the manual?

InFocus IN5122 Specifications

General IconGeneral
Matrix size0.63 \
Number of colors16.78 million colors
Native aspect ratio4:3
Projection distance- m
Projection technology3LCD
Supported aspect ratios4:3, 5:4, 16:9, 16:10
Contrast ratio (typical)2000:1
Screen size compatibility35.4 - 358 \
Projector native resolutionXGA (1024x768)
Vertical synchronization (max)120 kHz
Vertical synchronization (min)50 kHz
Horizontal synchronization (max)106 kHz
Horizontal synchronization (min)15 kHz
FocusManual
Throw ratio1.5 - 2.5:1
Zoom capabilityYes
Focal length range- mm
Vertical lens shift range-20 - 0 °
Horizontal lens shift range-20 - 20 %
Lamp typeUHP
Lamp power245 W
Light source typeLamp
Service life of light source3000 h
Service life of light source (economic mode)5000 h
3D-
Full HDNo
Supported video modes1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format systemNTSC, PAL, SECAM
Supported graphics resolutions1600 x 1200 (UXGA)
RMS rated power16 W
Number of built-in speakers2
BNC input ports5
USB connector typeUSB Type-A, USB Type-B
Serial interface typeRS-232
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity1
Ethernet LAN data rates10, 100 Mbit/s
Cables includedAC, RCA, VGA
Power consumption (standby)- W
Noise level32 dB
CertificationUL, c-UL, FCC, CE
On Screen Display (OSD) languagesCHI (SIMPL), CHI (TR), DAN, DEU, DUT, ENG, ESP, FIN, FRE, ITA, KOR, NOR, POL, POR, RUS, SWE, TUR
PlacementDesktop, Ceiling
Product typeStandard throw projector
Product colorBlack
Cable lock slot typeKensington
Operating altitude0 - 2286 m
Operating temperature (T-T)5 - 35 °C
Weight and Dimensions IconWeight and Dimensions
Depth318.5 mm
Width401 mm
Height111 mm
Weight4800 g
Package depth420 mm
Package width560 mm
Package height197 mm
Package weight8200 g

Related product manuals