JVC XL-R5010BKC User Manual

17
English English
It is possible to select your own program (order of tracks being
played) using the program playback mode. Any of the tracks (1-99)
on the CDs in the trays of the 3-CD changer can be selected.
If you want to program and record tracks, see “Program Edit
Recording” on page 27.
1
Load CDs into the trays of the 3-CD changer.
• Only tracks on the CDs loaded in the 3-CD changer can be reg-
istered into the program (i.e., tracks on a CD loaded in the CDR
cannot be selected for playback).
•“CD READ DISC” will be shown in the information display as
the unit reads the information from each disc.
Note
• To close a tray, press the 0 button for the tray number that is
open. If you press the 0 button for a tray number other than that
for the tray that is open, the program may not be played correctly.
2
Press the PLAY MODE button when the unit is
in the CD stop mode.
• The CD PLAYER indicator is shown in the display window,
PROGRAM indicator is shown in the display window, and if no
program has been registered, “PG NO PROGRAM” is shown in
the information display.
• If SET is pressed at this time, programming registration will
start (Step 3).
3
Press the SET button to start program
registration.
• The information display will show the following, and disc
source columns will flash.
4
Select the disc source (CD tray) by turning the
MULTI JOG control, and then press the SET but-
ton.
• When the SET button is pressed, next the programming step and
track number columns will flash.
5
Select and enter a track number (1-99) by
turning the MULTI JOG control, and then press
the SET button.
• The following is an example of track 2 on the CD in tray CD1
being entered as Step 1.
• When the SET button is pressed, the programming of Step 1 is
registered, and programming for Step 2 is ready.
6
Repeat Steps 4 and 5 to program up to a
maximum of 32 steps.
• If you try to program over 32 steps, “MEMORY FULL” is
shown in the information display, and the programming func-
tion ends automatically.
• Pressing the CD Control STOP 7 button on the main unit ends
the programming function.
Programming Playback Using
Main Unit Controls
STANDBY
STANDBY/ON
PLAY & EXCHANGE
3
-
CD
MAXMIN
PHONES
PLAY MODE
PHONES LEVEL
EJECT
REC SOURCE SELECTOR
MIX BLANCE
CD
LINE
LINE
MIC
MULTI JOG
/REC LEVEL
+
–
MIC
CANCELSETMENU
PAUSE
REC/
REC MUTING
PLAYSTOP
SYNCHRO
CD EDIT CD REC
STOP PLAY PAUSE
FINALIZE
MICLINECDDIGITAL
2 7 3,4,5
1 4,5
Program step
number
Disc source
Track number
Programming
step number
Disc source
Track number
MULTI JOG
REC LEVEL
+
–
SET
1. Select the disc. 2. Enter the selection.
=
CD1
+=
CD2
+=
CD3
+
MULTI JOG
REC LEVEL
+
–
SET
1. Select the track.
2. Enter the selection.
XL-R5010BK.book Page 17 Monday, June 4, 2001 11:40 AM

JVC XL-R5010BKC Specifications

Power

power requirements	120V, 60Hz
power consumption (power ON mode)	40W
power consumption (STANDBY mode)	5W

Output Terminals

analog output	2V/5kΩ
headphones output	4mW/32Ω
digital optical output	–21dBm - –15 dBm

Weight and Dimensions

dimensions (W x H x D)	435mm x 127mm x 334mm
mass	6.3kg