Lenze Global Drive 9300 Servo PLC Series - Page 128

9300 Servo PLC
Index
4-2
l
ServoPLC EN 2.0
I
Inputs
Analog. See A na l o g i nput s
Definition, 1-6
Di gi t a l . See Di gi t a l i nput s
Inputs_AIF1, 2-2
Inputs_AIF2, 2-7
Inputs_AIF3, 2-11
Inputs_ANALOG1, 2-16
Inputs_ANALOG2, 2-18
Inputs_DIGITAL, 2-36
Inputs_MCTRL, 2-41
Internalmotor control (MCTRL), 2-40
Additional torque setpoint, 2-43
Chopper frequency changeover , 2-49
Current controller, 2-43
Feedback system, 2-50
Field weakening, 2-49
Maximum speed, 2-44
MCTRL_nNAct_v, 2-51
Monitoring, 2-54
Earth fault, 2-56
Heatsink temperature (adjustable), 2-62
Heatsink temperature (fixed), 2-61
Ixt overload, 2-57
Motor temperature (adjustable), 2-63
Motor temperature (fixed), 2-61
Motor temperature (PTC), 2-64
Overvoltage, 2-58
Resolver, 2-65
Short-circuit, 2-56
Speed, 2-66
Undervoltage, 2-60
Phase controller, Phase controller influence, 2-47
Quick stop (QSP), 2-48
Speed controller, 2-45
Speed setpoint limitation, 2-46
System error messages, 2-55
LU, 2-60
NMAX, 2-66
OC1, 2-56
OC2, 2-56
OC5, 2-57
OH, 2-61
OH3, 2-61
OH4, 2-62
OH7, 2-63
OH8, 2-64
Sd2, 2-65
OU, 2-58
Torque control with speed limit, 2-46
Torque limitation, 2-44
Touch probe, 2-50
K
Keypad, Status messages, 3-10
L
LECOM, Status word C0150, 3-11
LED, 3-10
M
Maximum speed, 2-44
M C T R L_ M ot or C on t r ol . See Internal motor control
MCTRL_nNmaxC11, 2-44
Message, 2-55
Module numbers, 1-4
Monitoring, 2-54
Earth fault, 2-56
FAIL-QSP, 2-55
Heatsink temperature (adjustable), 2-62
Heatsink temperature (fixed), 2-61
Ixt overload, 2-57
Message, 2-55
Motor temperature (adjustable), 2-63
Motor temperature (fixed), 2-61
Motor temperature (PTC), 2-64
Overvoltage, 2-58
Resolver, 2-65
Short-circuit, 2-56
Speed, 2-66
Undervoltage, 2-60
Warning, 2-55
Motor control. See Internal motor control
Motor data, 2-52
N
Networking, 3-1
Normalisations, 1-8
O
Open-circuit monitoring, Resolver, 2-65
Operation inhibited(DISABLE), 2-22
Outputs
Analog. See Analog output s
Definition, 1-6
Di gi t a l . See Di gi t a l o ut put s
Outputs_AIF1, 2-5
Outputs_AIF2, 2-9
Outputs_AIF3, 2-13
Outputs_ANALOG1, 2-17
Outputs_ANALOG2, 2-19
Outputs_DIGITAL, 2-37
Outputs_MCTRL, 2-42
Overcurrent diagram, 2-57
efesotomasyon.com - Lenze
Show/Hide Bookmarks